Disabling IRQ #11

sardylan · Messaggio da **sardylan** » gio 28 ago 2008, 11:24

Salve a tutti... E' da un po' che non mi faccio un giro sul forum...
Ho notato che mi si è presentato di nuovo un vecchio problema per il quale vi avevo già chiesto aiuto...
In pratica, ho il serverino che uso come archivio dati... Avevo la 12.0 ed avevo risolto tutti questi problemi ricompilando il kernel...
Ora gli ho messo la 12.1, e sono andato in FTP per recuperarmi i 12-13 GB di dati che gli avevo archiviato...
Nel frattempo ero in SSH per re-impostare i permessi e mi è apparsa questa roba:

Codice: Seleziona tutto

root@perseo:~#
Message from syslogd@perseo at Thu Aug 28 11:14:16 2008 ...
perseo kernel: [ 4752.400705] Disabling IRQ #11

due o tre secondi dopo che ho iniziato il trasferimento dei dati...
Naturalmente ho provato a ricompilare il kernel, ma non sono riuscito a risolvere il problema... Poi ho provato a prendere il vecchio config, allinearlo e compilare con quello, ma niente da fare... Lo fa lo stesso...
Però, al contrario della 12.0, nonostante il messaaggio la velocità di trasferimento dei dati rimane sempre sui 10-11 MB/s...
Esiste un qualcosa per capire l'IRQ 11 a che cosa sia assegnato?? Qualche comando o qualcosa da frugare in /proc???
Qualche consiglio?? Vi occorrono infor più dettagliate???
Fatemi sapere!!!
Grazie a tutti!!!
Ciao!!!

YouTube · Messaggio da **conraid** » gio 28 ago 2008, 11:34

cat /proc/interrupts

sardylan · Messaggio da **sardylan** » gio 28 ago 2008, 12:54

Many thanks conraid...
Questo è l'output di cat /proc/interrupts

Codice: Seleziona tutto

root@perseo:~# cat /proc/interrupts
           CPU0
  0:         65   IO-APIC-edge      timer
  1:          2   IO-APIC-edge      i8042
  7:          0   IO-APIC-edge      parport0
  8:          1   IO-APIC-edge      rtc
  9:          1   IO-APIC-fasteoi   acpi
 11:     500001   IO-APIC-fasteoi   uhci_hcd:usb7, uhci_hcd:usb8
 12:          4   IO-APIC-edge      i8042
 14:      99372   IO-APIC-edge      ide0
 16:          8   IO-APIC-fasteoi   ehci_hcd:usb1, ohci_hcd:usb5
 17:          0   IO-APIC-fasteoi   ohci_hcd:usb6, EMU10K1
 18:          0   IO-APIC-fasteoi   ehci_hcd:usb2, ohci_hcd:usb3
 19:   11438637   IO-APIC-fasteoi   ide2, ohci_hcd:usb4, eth0
NMI:          0   Non-maskable interrupts
LOC:    2774432   Local timer interrupts
TRM:          0   Thermal event interrupts
SPU:          0   Spurious interrupts
ERR:          0
MIS:          0
root@perseo:~#

E qui nasce il casino!!! Credevo che fosse qualcosa relativa ai controller IDE... Invece è qualcosa relativo all'USB...
Questa mi è nuova... Secondo voi da che cosa dipende???
Inoltre, che cosa indica la colonna CPU0???

Ecco l'output di lsusb (non c'è praticamente niente collegato):

Codice: Seleziona tutto

root@perseo:~# lsusb
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
root@perseo:~#

E visto che ci siamo vi posto anche l'output di lspci:

Codice: Seleziona tutto

root@perseo:~# lspci -vv
00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-760 [IGD4-1P] System Controller (rev 14)
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
        Latency: 32
        Region 0: Memory at e8000000 (32-bit, prefetchable) [size=64M]
        Region 1: Memory at ee008000 (32-bit, prefetchable) [size=4K]
        Region 2: I/O ports at b000 [disabled] [size=4]
        Capabilities: [a0] AGP version 2.0
                Status: RQ=16 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
                Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
        Kernel driver in use: agpgart-amdk7

00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-760 [IGD4-1P] AGP Bridge (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 32
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
        I/O behind bridge: 0000a000-0000afff
        Memory behind bridge: ec000000-edffffff
        Prefetchable memory behind bridge: e0000000-e7ffffff
        Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
        Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: parport_pc

00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
        Subsystem: VIA Technologies, Inc. VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 32
        Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
        Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
        Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
        Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
        Region 4: I/O ports at b400 [size=16]
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: VIA_IDE

00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a) (prog-if 00 [UHCI])
        Subsystem: First International Computer, Inc. VA-502 Mainboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 32, Cache Line Size: 32 bytes
        Interrupt: pin D routed to IRQ 11
        Region 4: I/O ports at b800 [size=32]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: uhci_hcd

00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a) (prog-if 00 [UHCI])
        Subsystem: First International Computer, Inc. VA-502 Mainboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 32, Cache Line Size: 32 bytes
        Interrupt: pin D routed to IRQ 11
        Region 4: I/O ports at bc00 [size=32]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: uhci_hcd

00:07.4 SMBus: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
        Subsystem: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Interrupt: pin ? routed to IRQ 9
        Capabilities: [68] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0a.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
        Subsystem: Belkin Root Hub
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 32 (250ns min, 10500ns max), Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 18
        Region 0: Memory at ee004000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: ohci_hcd

00:0a.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
        Subsystem: Belkin Root Hub
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 32 (250ns min, 10500ns max), Cache Line Size: 32 bytes
        Interrupt: pin B routed to IRQ 19
        Region 0: Memory at ee005000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: ohci_hcd

00:0a.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20 [EHCI])
        Subsystem: Belkin Root Hub
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 32 (4000ns min, 8500ns max), Cache Line Size: 64 bytes
        Interrupt: pin C routed to IRQ 16
        Region 0: Memory at ee006000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: ehci_hcd

00:0c.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Interrupt: pin A routed to IRQ 16
        Region 0: I/O ports at c000 [size=32]
        Kernel driver in use: ne2k-pci

00:0d.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 07)
        Subsystem: Creative Labs SBLive! Player 5.1
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 32 (500ns min, 5000ns max)
        Interrupt: pin A routed to IRQ 17
        Region 0: I/O ports at c400 [size=32]
        Capabilities: [dc] Power Management version 1
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: EMU10K1_Audigy
        Kernel modules: snd-emu10k1

00:0d.1 Input device controller: Creative Labs SB Live! Game Port (rev 07)
        Subsystem: Creative Labs Gameport Joystick
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 32
        Region 0: I/O ports at c800 [size=8]
        Capabilities: [dc] Power Management version 1
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: Emu10k1_gameport

00:0f.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
        Subsystem: Realtek Semiconductor Co., Ltd. RT8139
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 32 (8000ns min, 16000ns max)
        Interrupt: pin A routed to IRQ 19
        Region 0: I/O ports at cc00 [size=256]
        Region 1: Memory at ee007000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: 8139too

00:10.0 RAID bus controller: Promise Technology, Inc. PDC20276 (MBFastTrak133 Lite) (rev 01) (prog-if 85)
        Subsystem: Promise Technology, Inc. MBFastTrak133 Lite (tm) Controller (RAID mode)
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 32 (1000ns min, 4500ns max), Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 19
        Region 0: I/O ports at d000 [size=8]
        Region 1: I/O ports at d400 [size=4]
        Region 2: I/O ports at d800 [size=8]
        Region 3: I/O ports at dc00 [size=4]
        Region 4: I/O ports at e000 [size=16]
        Region 5: Memory at ee000000 (32-bit, non-prefetchable) [size=16K]
        Capabilities: [60] Power Management version 1
                Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: Promise_IDE

00:11.0 USB Controller: NEC Corporation USB (rev 41) (prog-if 10 [OHCI])
        Subsystem: NEC Corporation Hama USB 2.0 CardBus
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 32 (250ns min, 10500ns max), Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at ee009000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: ohci_hcd

00:11.1 USB Controller: NEC Corporation USB (rev 41) (prog-if 10 [OHCI])
        Subsystem: NEC Corporation Hama USB 2.0 CardBus
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 32 (250ns min, 10500ns max), Cache Line Size: 32 bytes
        Interrupt: pin B routed to IRQ 17
        Region 0: Memory at ee00a000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: ohci_hcd

00:11.2 USB Controller: NEC Corporation USB 2.0 (rev 02) (prog-if 20 [EHCI])
        Subsystem: Giga-byte Technology Unknown device 5004
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 32 (4000ns min, 8500ns max), Cache Line Size: 64 bytes
        Interrupt: pin C routed to IRQ 18
        Region 0: Memory at ee00b000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: ehci_hcd

01:05.0 VGA compatible controller: ATI Technologies Inc Radeon R100 QD [Radeon 7200] (prog-if 00 [VGA controller])
        Subsystem: ATI Technologies Inc Radeon 7000/Radeon
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 32 (2000ns min), Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
        Region 1: I/O ports at a000 [size=256]
        Region 2: Memory at ed000000 (32-bit, non-prefetchable) [size=512K]
        [virtual] Expansion ROM at ec000000 [disabled] [size=128K]
        Capabilities: [58] AGP version 2.0
                Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
                Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: radeonfb

root@perseo:~#

Non ho proprio idea da che cosa dipenda!!

Messaggio da **phobos3576** » gio 28 ago 2008, 14:55

A volte questi problemi si risolvono dal BIOS.
In pratica, nel BIOS ci dovrebbe essere una opzione (se non erro, nella sezione BUS PCI) per decidere se le varie IRQ debbano essere assegnate dal sistema operativo o dallo stesso BIOS; prova a modificare quell'opzione per vedere cosa succede.

sardylan · Messaggio da **sardylan** » gio 28 ago 2008, 18:28

Ok!! Appena mi restituiscono il monitor provo a vedere nel bios...
Edit::: Grazie a tutti!!!

Messaggio da **Luci0** » gio 28 ago 2008, 20:39

Il kernel é lo huge o l' hai ricompilato ...?

sardylan · Messaggio da **sardylan** » gio 28 ago 2008, 22:53

@ Luci0
Il kernel con cui si verifica l'errore che vedi nel post di sopra e' un kernel ricompilato... 2.6.25.13 se non sbaglio...

slacky.eu

Disabling IRQ #11

Disabling IRQ #11

Re: Disabling IRQ #11

Re: Disabling IRQ #11

Re: Disabling IRQ #11

Re: Disabling IRQ #11

Re: Disabling IRQ #11

Re: Disabling IRQ #11