dmesg
Linux version 2.4.31 (root@tree) (gcc version 3.3.5) #8 Sun Jun 5 19:08:07 PDT 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000bfd0000 (usable)
BIOS-e820: 000000000bfd0000 - 000000000bfdf000 (ACPI data)
BIOS-e820: 000000000bfdf000 - 000000000bfe0000 (ACPI NVS)
BIOS-e820: 000000000bfe0000 - 000000000c000000 (reserved)
BIOS-e820: 00000000fffe0000 - 0000000100000000 (reserved)
191MB LOWMEM available.
On node 0 totalpages: 49104
zone(0): 4096 pages.
zone(1): 45008 pages.
zone(2): 0 pages.
ACPI disabled because your bios is from 99 and too old
You can enable it with acpi=force
IBM machine detected. Enabling interrupts during APM calls.
Kernel command line: BOOT_IMAGE=Linux ro root=303 acpi=off pci=noacpi agp=off
Initializing CPU#0
Detected 232.107 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 462.02 BogoMIPS
Memory: 190872k/196416k available (1960k kernel code, 5156k reserved, 649k data, 132k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After generic, caps: 0183f9ff 00000000 00000000 00000000
CPU: Common caps: 0183f9ff 00000000 00000000 00000000
CPU: Intel Pentium II (Deschutes) stepping 02
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (
rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
PCI: PCI BIOS revision 2.10 entry at 0xfd880, last bus=6
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router PIIX/ICH [8086/7110] at 00:07.0
PCI: Found IRQ 11 for device 00:02.0
PCI: Sharing IRQ 11 with 00:03.0
PCI: Found IRQ 11 for device 00:02.1
Limiting direct PCI/PCI transfers.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
vesafb: framebuffer at 0xe0000000, mapped to 0xcc80d000, size 1875k
vesafb: mode is 800x600x16, linelength=1600, pages=1
vesafb: protected mode interface info at c000:8e10
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 100x37
fb0: VESA VGA frame buffer device
pty: 512 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
Real Time Clock Driver v1.10f
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
RAMDISK driver initialized: 16 RAM disks of 7777K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfcf0-0xfcf7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfcf8-0xfcff, BIOS settings: hdc:DMA, hdd:pio
hda: IBM-DYKA-23240, ATA DISK drive
blk: queue c03dd8e0, I/O limit 4095Mb (mask 0xffffffff)
hdc: TOSHIBA CD-ROM XM-1902B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: 6354432 sectors (3253 MB) w/90KiB Cache, CHS=788/128/63, UDMA(33)
hdc: attached ide-cdrom driver.
hdc: ATAPI 24X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.12
Partition check:
hda: hda1 hda2 hda3
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
8regs : 384.000 MB/sec
32regs : 220.800 MB/sec
pII_mmx : 525.200 MB/sec
p5_mmx : 542.400 MB/sec
raid5: using function: p5_mmx (542.400 MB/sec)
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
LVM version 1.0.8(17/11/2003)
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 132k freed
Adding Swap: 201592k swap-space (priority -1)
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 149M
agpgart: no supported devices found.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Intel ISA PCIC probe: not found.
Databook TCIC-2 PCMCIA probe: not found.
PCI: Found IRQ 11 for device 00:02.0
PCI: Sharing IRQ 11 with 00:03.0
PCI: Found IRQ 11 for device 00:02.1
Yenta ISA IRQ mask 0x0698, PCI irq 11
Socket status: 30000020
Yenta ISA IRQ mask 0x0698, PCI irq 11
Socket status: 30000006
cs: cb_alloc(bus 1): vendor 0xffff, device 0x9066
PCI: Enabling device 01:00.0 (0000 -> 0002)
cs: IO port probe 0x0100-0x03ff: excluding 0x130-0x137 0x200-0x207 0x220-0x22f 0x388-0x38f 0x3b8-0x3df
cs: IO port probe 0x0a00-0x0aff: clean.
cs: IO port probe 0x0600-0x06ff: clean.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
uhci.c: USB Universal Host Controller Interface driver v1.1
PCI: Found IRQ 11 for device 00:07.2
uhci.c: USB UHCI at I/O 0x8400, IRQ 11
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
ALSA ../../alsa-kernel/isa/cs423x/cs4231_lib.c:1568: CS4232 control port features are not accessible
acx100: It looks like you've been coaxed into buying a wireless network card
acx100: that uses the mysterious ACX100/ACX111 chip from Texas Instruments.
acx100: You should better have bought e.g. a PRISM(R) chipset based card,
acx100: since that would mean REAL vendor Linux support.
acx100: Given this info, it's evident that this driver is still EXPERIMENTAL,
acx100: thus your mileage may vary. Reading README file and/or Craig's HOWTO is
recommended, visit
http://acx100.sf.net in case of further questions/discussion.
acx100: Compiled to use 32bit I/O access (faster, however I/O timing issues might occur, such as non-working firmware upload!) instead of 16bit access
Running on a little-endian CPU
acx_init_module: TI acx_pci.o: Ver 0.2.0pre8 driver initialized, waiting for cards to probe...
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Intel ISA PCIC probe: not found.
hub.c: new USB device 00:07.2-1, assigned address 2
usb.c: USB device 2 (vend/prod 0x4586/0x1026) is not claimed by any active driver.
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
scsi1 : SCSI emulation for USB Mass Storage devices
Vendor: Model: USB BAR Rev: 1.13
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
SCSI device sda: 2031616 512-byte hdwr sectors (1040 MB)
sda: Write Protect is off
sda: sda1
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
USB Mass Storage support registered.
usb.c: USB disconnect on device 00:07.2-1 address 2
lspci
00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (AGP disabled) (rev 02)
00:02.0 CardBus bridge: Texas Instruments PCI1250 (rev 02)
00:02.1 CardBus bridge: Texas Instruments PCI1250 (rev 02)
00:03.0 VGA compatible controller: Neomagic Corporation NM2160 [MagicGraph 128XD] (rev 01)
00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 01)
00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01)
00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01)
00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 01)
01:00.0 Network controller: Illegal Vendor ID: Unknown device 9066
lspci -H1
00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (AGP disabled) (rev 02)
00:02.0 CardBus bridge: Texas Instruments PCI1250 (rev 02)
00:02.1 CardBus bridge: Texas Instruments PCI1250 (rev 02)
00:03.0 VGA compatible controller: Neomagic Corporation NM2160 [MagicGraph 128XD] (rev 01)
00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 01)
00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01)
00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01)
00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 01)
01:00.0 Network controller: Texas Instruments ACX 111 54Mbps Wireless Interface
lspci -n
00:00.0 Class 0600: 8086:7192 (rev 02)
00:02.0 Class 0607: 104c:ac16 (rev 02)
00:02.1 Class 0607: 104c:ac16 (rev 02)
00:03.0 Class 0300: 10c8:0004 (rev 01)
00:07.0 Class 0680: 8086:7110 (rev 01)
00:07.1 Class 0101: 8086:7111 (rev 01)
00:07.2 Class 0c03: 8086:7112 (rev 01)
00:07.3 Class 0680: 8086:7113 (rev 01)
01:00.0 Class 0280: ffff:9066
lspci -v
00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (AGP disabled) (rev 02)
Flags: bus master, medium devsel, latency 64
Memory at <unassigned> (32-bit, prefetchable) [size=256M]
00:02.0 CardBus bridge: Texas Instruments PCI1250 (rev 02)
Subsystem: IBM ThinkPad 600
Flags: bus master, medium devsel, latency 168, IRQ 11
Memory at 20301000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=01, subordinate=03, sec-latency=176
Memory window 0: 10000000-103ff000 (prefetchable)
Memory window 1: 10400000-107ff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
16-bit legacy interface ports at 0001
00:02.1 CardBus bridge: Texas Instruments PCI1250 (rev 02)
Subsystem: IBM ThinkPad 600
Flags: bus master, medium devsel, latency 168, IRQ 11
Memory at 20300000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=04, subordinate=06, sec-latency=176
Memory window 0: 10800000-10bff000 (prefetchable)
Memory window 1: 10c00000-10fff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff
16-bit legacy interface ports at 0001
00:03.0 VGA compatible controller: Neomagic Corporation NM2160 [MagicGraph 128XD] (rev 01) (prog-if 00 [VGA])
Subsystem: Neomagic Corporation MagicGraph 128XD
Flags: bus master, medium devsel, latency 128, IRQ 11
Memory at e0000000 (32-bit, prefetchable) [size=16M]
Memory at 20000000 (32-bit, non-prefetchable) [size=2M]
Memory at 20200000 (32-bit, non-prefetchable) [size=1M]
00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 01)
Flags: bus master, medium devsel, latency 0
00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Flags: bus master, medium devsel, latency 48
I/O ports at fcf0 [size=16]
00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Flags: bus master, medium devsel, latency 48, IRQ 11
I/O ports at 8400 [size=32]
00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 01)
Flags: medium devsel, IRQ 9
01:00.0 Network controller: Illegal Vendor ID: Unknown device 9066
Subsystem: Abocom Systems Inc: Unknown device ab80
Flags: medium devsel, IRQ 11
Memory at 10400000 (32-bit, non-prefetchable) [size=8K]
Memory at 10420000 (32-bit, non-prefetchable) [size=128K]
Capabilities: [40] Power Management version 2
lspci -vv
00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (AGP disabled) (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 64
Region 0: Memory at <unassigned> (32-bit, prefetchable) [size=256M]
00:02.0 CardBus bridge: Texas Instruments PCI1250 (rev 02)
Subsystem: IBM ThinkPad 600
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 04
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 20301000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=01, subordinate=03, sec-latency=176
Memory window 0: 10000000-103ff000 (prefetchable)
Memory window 1: 10400000-107ff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
00:02.1 CardBus bridge: Texas Instruments PCI1250 (rev 02)
Subsystem: IBM ThinkPad 600
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 04
Interrupt: pin B routed to IRQ 11
Region 0: Memory at 20300000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=04, subordinate=06, sec-latency=176
Memory window 0: 10800000-10bff000 (prefetchable)
Memory window 1: 10c00000-10fff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:03.0 VGA compatible controller: Neomagic Corporation NM2160 [MagicGraph 128XD] (rev 01) (prog-if 00 [VGA])
Subsystem: Neomagic Corporation MagicGraph 128XD
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (4000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at 20000000 (32-bit, non-prefetchable) [size=2M]
Region 2: Memory at 20200000 (32-bit, non-prefetchable) [size=1M]
00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 48
Region 4: I/O ports at fcf0 [size=16]
00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 48
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at 8400 [size=32]
00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 01)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
01:00.0 Network controller: Illegal Vendor ID: Unknown device 9066
Subsystem: Abocom Systems Inc: Unknown device ab80
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 10400000 (32-bit, non-prefetchable) [size=8K]
Region 1: Memory at 10420000 (32-bit, non-prefetchable) [size=128K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-