Repository 32bit  Forum
Repository 64bit  Wiki

ZENWALK 6.0: problemi con eth0

Forum dedicato ai Porting ufficiali e non di Slackware, vedi Slack/390, ARMedslack, Slamd64, Slackintosh, Ocsid, Sloox, Zenwalk, How-Tux, Slax etc etc

Moderatore: Staff

Regole del forum
1) Specificare nome e versione del porting.
2) Specificare se discussione/suggerimento o richiesta d'aiuto.
3) Leggere attentamente le risposte ricevute
4) Scrivere i messaggi con il colore di default, evitare altri colori.
5) Scrivere in Italiano o in Inglese, se possibile grammaticalmente corretto, evitate stili di scrittura poco chiari, quindi nessuna abbreviazione tipo telegramma o scrittura stile SMS o CHAT.
6) Appena registrati è consigliato presentarsi nel forum dedicato.

La non osservanza delle regole porta a provvedimenti di vari tipo da parte dello staff, in particolare la non osservanza della regola 5 porta alla cancellazione del post e alla segnalazione dell'utente. In caso di recidività l'utente rischia il ban temporaneo.

ZENWALK 6.0: problemi con eth0

Messaggioda Kernel-Panic » dom ott 25, 2009 21:03

Ciao a tutti, ho installato la Zenwalk 6.0 su un PC. Poichè il kernel installato era il 2.6.28.7 ho deciso di installare il kernel precompilato di Pat (precisamente il 2.6.29.6-smp-generic) seguendo questa procedura. Ho riavviato la macchina senza alcun tipo di problema. Ma, dopo aver fatto questo, non andava più la connessione alla rete cablata eth0, cosa che non succedeva con il kernel vecchio. Allora da shell ho avviato netconfig e ho impostato tutto (così come avevo fatto quando era installato il vecchio kernel). Ho avviato la rete, ma niente da fare! eth0 non veniva rilevata da wicd. Quale può essere il problema? :-k

Di seguito posto il contenuto di alcuni comandi.

1) Output del comando lsmod:

Codice: Seleziona tutto
Module                  Size  Used by
ipv6                  243508  16
pcmcia                 33772  0
pcmcia_core            32016  1 pcmcia
i915                  151464  2
drm                   137856  3 i915
i2c_algo_bit            5504  1 i915
iptable_mangle          2332  0
iptable_nat             4796  0
nf_nat                 16208  1 iptable_nat
nf_conntrack_ipv4      12520  3 iptable_nat,nf_nat
nf_conntrack           53844  3 iptable_nat,nf_nat,nf_conntrack_ipv4
nf_defrag_ipv4          1532  1 nf_conntrack_ipv4
iptable_filter          2268  0
ip_tables              10892  3 iptable_mangle,iptable_nat,iptable_filter
x_tables               13280  2 iptable_nat,ip_tables
fuse                   54008  6
3c59x                  39908  0
lp                      9316  0
sg                     24912  0
gspca_pac207            6428  0
gspca_main             21564  1 gspca_pac207
videodev               38688  1 gspca_main
v4l1_compat            13184  1 videodev
usb_storage            96096  1
cdc_ether               4732  0
usbnet                 13764  1 cdc_ether
mii                     4380  2 3c59x,usbnet
snd_intel8x0           28696  1
iTCO_wdt               10624  0
intel_agp              25628  1
iTCO_vendor_support     2848  1 iTCO_wdt
rtc_cmos               10124  0
snd_ac97_codec        100128  1 snd_intel8x0
thermal                15096  0
rtc_core               15992  1 rtc_cmos
psmouse                41676  0
parport_pc             24036  1
processor              38600  1 thermal
agpgart                29256  3 drm,intel_agp
shpchp                 31888  0
serio_raw               5024  0
pcspkr                  2204  0
ac97_bus                1372  1 snd_ac97_codec
rtc_lib                 2332  1 rtc_core
thermal_sys            10756  2 thermal,processor
parport                30700  2 lp,parport_pc
snd_pcm                68128  2 snd_intel8x0,snd_ac97_codec
ehci_hcd               35240  0
dcdbas                  7068  0
snd_timer              19108  1 snd_pcm
button                  5708  0
snd                    50820  6 snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer
uhci_hcd               22284  0
hwmon                   2104  1 thermal_sys
soundcore               5824  1 snd
i2c_i801                8784  0
snd_page_alloc          7972  2 snd_intel8x0,snd_pcm
i2c_core               20496  4 i915,drm,i2c_algo_bit,i2c_i801
evdev                   9152  3
reiserfs              230176  1


2) Output del comando dmesg:

Codice: Seleziona tutto
Linux version 2.6.29.6-smp (root@midas) (gcc version 4.3.3 (GCC) ) #1 SMP Mon Aug 17 00:18:05 CDT 2009
KERNEL supported cpus:
  Intel GenuineIntel
  AMD AuthenticAMD
  NSC Geode by NSC
  Cyrix CyrixInstead
  Centaur CentaurHauls
  Transmeta GenuineTMx86
  Transmeta TransmetaCPU
  UMC UMC UMC UMC
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000002fe70000 (usable)
 BIOS-e820: 000000002fe70000 - 000000002fe72000 (ACPI NVS)
 BIOS-e820: 000000002fe72000 - 000000002fe93000 (ACPI data)
 BIOS-e820: 000000002fe93000 - 000000002ff00000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fecf0000 - 00000000fecf1000 (reserved)
 BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
 BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
DMI 2.3 present.
last_pfn = 0x2fe70 max_arch_pfn = 0x100000
kernel direct mapping tables up to 2fe70000 @ 7000-c000
RAMDISK: 00e1a000 - 00effdbc
ACPI: RSDP 000FEB90, 0014 (r0 DELL  )
ACPI: RSDT 000FD28B, 0034 (r1 DELL    3000           8 ASL        61)
ACPI: FACP 000FD2BF, 0074 (r1 DELL    3000           8 ASL        61)
FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4)
ACPI: DSDT FFFCF6B6, 24C9 (r1   DELL    dt_ex     1000 MSFT  100000D)
ACPI: FACS 2FE70000, 0040
ACPI: SSDT FFFD1B7F, 00A7 (r1   DELL    st_ex     1000 MSFT  100000D)
ACPI: APIC 000FD333, 006C (r1 DELL    3000           8 ASL        61)
ACPI: BOOT 000FD39F, 0028 (r1 DELL    3000           8 ASL        61)
ACPI: Local APIC address 0xfee00000
0MB HIGHMEM available.
766MB LOWMEM available.
  mapped low ram: 0 - 2fe70000
  low ram: 00000000 - 2fe70000
  bootmap 00008000 - 0000dfd0
(9 early reservations) ==> bootmem [0000000000 - 002fe70000]
  #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
  #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
  #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
  #3 [0000100000 - 0000638024]    TEXT DATA BSS ==> [0000100000 - 0000638024]
  #4 [0000e1a000 - 0000effdbc]          RAMDISK ==> [0000e1a000 - 0000effdbc]
  #5 [0000639000 - 000063c000]    INIT_PG_TABLE ==> [0000639000 - 000063c000]
  #6 [000009d800 - 0000100000]    BIOS reserved ==> [000009d800 - 0000100000]
  #7 [0000007000 - 0000008000]          PGTABLE ==> [0000007000 - 0000008000]
  #8 [0000008000 - 000000e000]          BOOTMAP ==> [0000008000 - 000000e000]
found SMP MP-table at [c00fe710] 000fe710
Zone PFN ranges:
  DMA      0x00000000 -> 0x00001000
  Normal   0x00001000 -> 0x0002fe70
  HighMem  0x0002fe70 -> 0x0002fe70
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0: 0x00000000 -> 0x000000a0
    0: 0x00000100 -> 0x0002fe70
On node 0 totalpages: 196112
free_area_init_node: node 0, pgdat c053d880, node_mem_map c1000000
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 3968 pages, LIFO batch:0
  Normal zone: 1501 pages used for memmap
  Normal zone: 190611 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 4 CPUs, 3 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
Allocating PCI resources starting at 30000000 (gap: 2ff00000:ced00000)
NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:4 nr_node_ids:1
PERCPU: Allocating 40960 bytes of per cpu data
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 194579
Kernel command line: BOOT_IMAGE=Zenwalk2.6.29.6 ro root=802 resume=/dev/sda3 splash=silent
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Fast TSC calibration using PIT
Detected 2992.370 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 770760k/784832k available (3131k kernel code, 13500k reserved, 1441k data, 364k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xffe19000 - 0xfffff000   (1944 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf0670000 - 0xff7fe000   ( 241 MB)
    lowmem  : 0xc0000000 - 0xefe70000   ( 766 MB)
      .init : 0xc0580000 - 0xc05db000   ( 364 kB)
      .data : 0xc040ed43 - 0xc0577508   (1441 kB)
      .text : 0xc0100000 - 0xc040ed43   (3131 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=12, HWalign=128, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Calibrating delay loop (skipped), value calculated using timer frequency.. 5984.74 BogoMIPS (lpj=2992370)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Hyper-Threading is disabled
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
using mwait in idle threads.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20081204
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 01
Brought up 1 CPUs
Total of 1 processors activated (5984.74 BogoMIPS).
net_namespace: 956 bytes
xor: automatically using best checksumming function: pIII_sse
   pIII_sse  :  4840.000 MB/sec
xor: using function: pIII_sse (4840.000 MB/sec)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfbbf8, last bus=1
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:00.0: reg 10 32bit mmio: [0xf0000000-0xf7ffffff]
pci 0000:00:02.0: reg 10 32bit mmio: [0xe8000000-0xefffffff]
pci 0000:00:02.0: reg 14 32bit mmio: [0xfeb80000-0xfebfffff]
pci 0000:00:02.0: reg 18 io port: [0xed98-0xed9f]
pci 0000:00:1d.0: reg 20 io port: [0xff80-0xff9f]
pci 0000:00:1d.1: reg 20 io port: [0xff60-0xff7f]
pci 0000:00:1d.3: reg 20 io port: [0xff20-0xff3f]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xffa80800-0xffa80bff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: HPET at 0xfed00000
pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 0880-08bf claimed by ICH4 GPIO
pci 0000:00:1f.1: reg 10 io port: [0x1f0-0x1f7]
pci 0000:00:1f.1: reg 14 io port: [0x3f4-0x3f7]
pci 0000:00:1f.1: reg 18 io port: [0x170-0x177]
pci 0000:00:1f.1: reg 1c io port: [0x374-0x377]
pci 0000:00:1f.1: reg 20 io port: [0xffa0-0xffaf]
pci 0000:00:1f.1: reg 24 32bit mmio: [0xfeb7fc00-0xfeb7ffff]
pci 0000:00:1f.3: reg 20 io port: [0xeda0-0xedbf]
pci 0000:00:1f.5: reg 10 io port: [0xee00-0xeeff]
pci 0000:00:1f.5: reg 14 io port: [0xedc0-0xedff]
pci 0000:00:1f.5: reg 18 32bit mmio: [0xfeb7fa00-0xfeb7fbff]
pci 0000:00:1f.5: reg 1c 32bit mmio: [0xfeb7f900-0xfeb7f9ff]
pci 0000:00:1f.5: PME# supported from D0 D3hot D3cold
pci 0000:00:1f.5: PME# disabled
pci 0000:01:00.0: reg 10 io port: [0xdf20-0xdf27]
pci 0000:01:00.0: reg 14 io port: [0xdf18-0xdf1b]
pci 0000:01:00.0: reg 18 io port: [0xdf28-0xdf2f]
pci 0000:01:00.0: reg 1c io port: [0xdf1c-0xdf1f]
pci 0000:01:00.0: reg 20 io port: [0xdf30-0xdf3f]
pci 0000:01:00.0: reg 24 32bit mmio: [0xfe9fec00-0xfe9fefff]
pci 0000:01:00.0: reg 30 32bit mmio: [0xfea00000-0xfea7ffff]
pci 0000:01:00.0: supports D1 D2
pci 0000:01:08.0: reg 10 32bit mmio: [0xfe9ff000-0xfe9fffff]
pci 0000:01:08.0: reg 14 io port: [0xdf40-0xdf7f]
pci 0000:01:08.0: supports D1 D2
pci 0000:01:08.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:01:08.0: PME# disabled
pci 0000:00:1e.0: transparent bridge
pci 0000:00:1e.0: bridge io port: [0xd000-0xdfff]
pci 0000:00:1e.0: bridge 32bit mmio: [0xfe900000-0xfeafffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 15)
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
hpet clockevent registered
HPET: 3 timers in total, 0 timers will be used for per-cpu timer
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:0b: io resource (0x800-0x85f) overlaps 0000:00:1f.0 BAR 7 (0x800-0x87f), disabling
pnp 00:0b: io resource (0x860-0x8ff) overlaps 0000:00:1f.0 BAR 7 (0x800-0x87f), disabling
pnp: PnP ACPI: found 12 devices
ACPI: ACPI bus type pnp unregistered
system 00:00: iomem range 0x0-0x9ffff could not be reserved
system 00:00: iomem range 0x100000-0xffffff could not be reserved
system 00:00: iomem range 0x1000000-0x2fe6ffff could not be reserved
system 00:00: iomem range 0xc0000-0xfffff could not be reserved
system 00:00: iomem range 0xfec00000-0xfec0ffff has been reserved
system 00:00: iomem range 0xfee00000-0xfee0ffff has been reserved
system 00:00: iomem range 0xfed20000-0xfed8ffff has been reserved
system 00:00: iomem range 0xfecf0000-0xfecf0fff has been reserved
system 00:00: iomem range 0xffb00000-0xffbfffff has been reserved
system 00:00: iomem range 0xffc00000-0xffffffff has been reserved
system 00:0b: ioport range 0xc00-0xc7f has been reserved
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01
pci 0000:00:1e.0:   IO window: 0xd000-0xdfff
pci 0000:00:1e.0:   MEM window: 0xfe900000-0xfeafffff
pci 0000:00:1e.0:   PREFETCH window: 0x00000030000000-0x000000300fffff
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:01: resource 0 io:  [0xd000-0xdfff]
pci_bus 0000:01: resource 1 mem: [0xfe900000-0xfeafffff]
pci_bus 0000:01: resource 2 mem: [0x30000000-0x300fffff]
pci_bus 0000:01: resource 3 io:  [0x00-0xffff]
pci_bus 0000:01: resource 4 mem: [0x000000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs... it is
Freeing initrd memory: 919k freed
Simple Boot Flag value 0x87 read from CMOS RAM was invalid
Simple Boot Flag at 0x7a set to 0x1
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1507
alg: No test for cipher_null (cipher_null-generic)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for fcrypt (fcrypt-generic)
alg: No test for stdrng (krng)
async_tx: api initialized (async)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:02.0: Boot video device
pci 0000:01:08.0: Firmware left e100 interrupts enabled; disabling
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
brd: module loaded
loop: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input0
Uniform Multi-Platform E-IDE driver
piix 0000:00:1f.1: IDE controller (0x8086:0x24db rev 0x02)
pci 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
piix 0000:00:1f.1: IDE port disabled
piix 0000:00:1f.1: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xffa0-0xffa7
Probing IDE interface ide0...
hda: HL-DT-ST GCE-8483B, ATAPI CD/DVD-ROM drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/33 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide-gd driver 1.18
ide-cd driver 5.00
ide-cd: hda: ATAPI 48X CD-ROM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
sata_sil 0000:01:00.0: version 2.4
sata_sil 0000:01:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
sata_sil 0000:01:00.0: Applying R_ERR on DMA activate FIS errata fix
scsi0 : sata_sil
scsi1 : sata_sil
scsi2 : sata_sil
scsi3 : sata_sil
ata1: SATA max UDMA/100 mmio m1024@0xfe9fec00 tf 0xfe9fec80 irq 21
ata2: SATA max UDMA/100 mmio m1024@0xfe9fec00 tf 0xfe9fecc0 irq 21
ata3: SATA max UDMA/100 mmio m1024@0xfe9fec00 tf 0xfe9fee80 irq 21
ata4: SATA max UDMA/100 mmio m1024@0xfe9fec00 tf 0xfe9feec0 irq 21
ata1: SATA link down (SStatus 0 SControl 310)
ata2: SATA link down (SStatus 0 SControl 310)
ata3: SATA link down (SStatus 0 SControl 310)
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata4.00: ATA-7: SAMSUNG HD250HJ, FH100-06, max UDMA7
ata4.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata4.00: configured for UDMA/100
scsi 3:0:0:0: Direct-Access     ATA      SAMSUNG HD250HJ  FH10 PQ: 0 ANSI: 5
sd 3:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
sd 3:0:0:0: [sda] Write Protect is off
sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 3:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
sd 3:0:0:0: [sda] Write Protect is off
sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3
sd 3:0:0:0: [sda] Attached SCSI disk
PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
raid6: int32x1    738 MB/s
raid6: int32x2    871 MB/s
raid6: int32x4    886 MB/s
raid6: int32x8    617 MB/s
raid6: mmxx1     1851 MB/s
raid6: mmxx2     2148 MB/s
raid6: sse1x1    1058 MB/s
raid6: sse1x2    1867 MB/s
raid6: sse2x1    2136 MB/s
raid6: sse2x2    2890 MB/s
raid6: using algorithm sse2x2 (2890 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: multipath personality registered for level -4
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
cpuidle: using governor ladder
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
Using IPI No-Shortcut mode
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
Freeing unused kernel memory: 364k freed
PM: Starting manual resume from disk
ReiserFS: sda2: found reiserfs format "3.6" with standard journal
ReiserFS: sda2: using ordered data mode
ReiserFS: sda2: journal params: device sda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda2: checking transaction log (sda2)
ReiserFS: sda2: Using r5 hash to sort names
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000ff80
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.29.6-smp uhci_hcd
usb usb1: SerialNumber: 0000:00:1d.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000ff60
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.29.6-smp uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.1
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.3: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000ff20
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.29.6-smp uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.3
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3
ACPI: Power Button (CM) [VBTN]
input: PC Speaker as /devices/platform/pcspkr/input/input4
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
processor ACPI_CPU:00: registered as cooling_device0
Linux agpgart interface v0.103
intel_rng: Firmware space is locked read-only. If you can't or
intel_rng: don't want to disable this in firmware setup, and if
intel_rng: you are certain that your system has a functional
intel_rng: RNG, try using the 'no_fwh_detect' option.
dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 128 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xffa80800
parport_pc 00:0a: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
usb 1-1: new full speed USB device using uhci_hcd and address 2
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: EHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.29.6-smp ehci_hcd
usb usb4: SerialNumber: 0000:00:1d.7
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 8 ports detected
agpgart-intel 0000:00:00.0: Intel 865 Chipset
agpgart-intel 0000:00:00.0: detected 892K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xe8000000
i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: Found a ICH5 or ICH5R TCO device (Version=1, TCOBASE=0x0860)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
rtc_cmos 00:05: RTC can wake from S4
rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one day, 242 bytes nvram, hpet irqs
hub 1-0:1.0: unable to enumerate USB device on port 1
Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
Intel ICH 0000:00:1f.5: setting latency timer to 64
usb 4-8: new high speed USB device using ehci_hcd and address 3
AC'97 0 analog subsections not ready
intel8x0_measure_ac97_clock: measured 50325 usecs
intel8x0: clocking to 48000
usb 4-8: New USB device found, idVendor=05e3, idProduct=0608
usb 4-8: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 4-8: Product: USB2.0 Hub
usb 4-8: configuration #1 chosen from 1 choice
hub 4-8:1.0: USB hub found
hub 4-8:1.0: 4 ports detected
usb 1-1: new full speed USB device using uhci_hcd and address 3
input: ImPS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio1/input/input5
usb 1-1: New USB device found, idVendor=0a5c, idProduct=6300
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1: Product: USB Network Interface
usb 1-1: Manufacturer: Broadcom Corporation
usb 1-1: SerialNumber: 00085cbc5aa5
usb 1-1: configuration #2 chosen from 2 choices
usb 4-8.2: new high speed USB device using ehci_hcd and address 4
eth0 (cdc_ether): not using net_device_ops yet
eth0: register 'cdc_ether' at usb-0000:00:1d.0-1, CDC Ethernet Device, 00:08:5c:bc:5a:a5
usbcore: registered new interface driver cdc_ether
usb 4-8.2: New USB device found, idVendor=0bc2, idProduct=3300
usb 4-8.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-8.2: Product: Desktop         
usb 4-8.2: Manufacturer: Seagate
usb 4-8.2: SerialNumber: 2GHJKZX0   
usb 4-8.2: configuration #1 chosen from 1 choice
usb 4-8.3: new full speed USB device using ehci_hcd and address 5
Initializing USB Mass Storage driver...
scsi4 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
usb 4-8.3: New USB device found, idVendor=093a, idProduct=2460
usb 4-8.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 4-8.3: Product: CIF Single Chip     
usb 4-8.3: Manufacturer: Pixart Imaging Inc.
usb 4-8.3: configuration #1 chosen from 1 choice
Linux video capture interface: v2.00
gspca: main v2.4.0 registered
gspca: probing 093a:2460
pac207: Pixart Sensor ID 0x27 Chips ID 0x09
pac207: Pixart PAC207BCA Image Processor and Control Chip detected (vid/pid 0x093A:0x2460)
gspca: probe ok
usbcore: registered new interface driver pac207
pac207: registered
usb 4-8.4: new high speed USB device using ehci_hcd and address 6
usb 4-8.4: New USB device found, idVendor=03f0, idProduct=2605
usb 4-8.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-8.4: Product: hp scanjet
usb 4-8.4: Manufacturer: hewlett packard
usb 4-8.4: SerialNumber: CN5A7A113W04CN
usb 4-8.4: configuration #1 chosen from 1 choice
scsi 4:0:0:0: Direct-Access     Seagate  Desktop          0130 PQ: 0 ANSI: 4
sd 4:0:0:0: [sdb] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
sd 4:0:0:0: [sdb] Write Protect is off
sd 4:0:0:0: [sdb] Mode Sense: 2f 08 00 00
sd 4:0:0:0: [sdb] Assuming drive cache: write through
sd 4:0:0:0: [sdb] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
sd 4:0:0:0: [sdb] Write Protect is off
sd 4:0:0:0: [sdb] Mode Sense: 2f 08 00 00
sd 4:0:0:0: [sdb] Assuming drive cache: write through
 sdb: sdb1
sd 4:0:0:0: [sdb] Attached SCSI disk
usb-storage: device scan complete
sd 3:0:0:0: Attached scsi generic sg0 type 0
sd 4:0:0:0: Attached scsi generic sg1 type 0
lp0: using parport0 (interrupt-driven).
lp0: console ready
fuse init (API version 7.11)
Adding 2650716k swap on /dev/sda3.  Priority:-1 extents:1 across:2650716k
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (12263 buckets, 49052 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[drm] Initialized drm 1.1.0 20060810
pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:02.0: setting latency timer to 64
[drm] Initialized i915 1.6.0 20080730 on minor 0
Intel ISA PCIC probe: not found.
Databook TCIC-2 PCMCIA probe: not found.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions


3) output del comando ifconfig (come si può vedere, eth0 non viene proprio vista):

Codice: Seleziona tutto
lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)



4) output del file rc.inet1.conf :

Codice: Seleziona tutto
# /etc/rc.d/rc.inet1.conf
#
# This file contains the configuration settings for network interfaces.
# If USE_DHCP[interface] is set to "yes", this overrides any other settings.
# If you don't have an interface, leave the settings null ("").

# You can configure network interfaces other than eth0,eth1... by setting
# IFNAME[interface] to the interface's name. If IFNAME[interface] is unset
# or empty, it is assumed you're configuring eth<interface>.

# Several other parameters are available, the end of this file contains a
# comprehensive set of examples.

# =============================================================================

# Config information for eth0:
IPADDR[0]="192.168.1.3"
NETMASK[0]="255.255.255.0"
USE_DHCP[0]=""
DHCP_HOSTNAME[0]=""

# Config information for eth1:
IPADDR[1]=""
NETMASK[1]=""
USE_DHCP[1]=""
DHCP_HOSTNAME[1]=""

# Config information for eth2:
IPADDR[2]=""
NETMASK[2]=""
USE_DHCP[2]=""
DHCP_HOSTNAME[2]=""

# Config information for eth3:
IPADDR[3]=""
NETMASK[3]=""
USE_DHCP[3]=""
DHCP_HOSTNAME[3]=""

# Default gateway IP address:
GATEWAY="192.168.1.1"

# Change this to "yes" for debugging output to stdout.  Unfortunately,
# /sbin/hotplug seems to disable stdout so you'll only see debugging output
# when rc.inet1 is called directly.
DEBUG_ETH_UP="no"

## Example config information for wlan0.  Uncomment the lines you need and fill
## in your info.  (You may not need all of these for your wireless network)
#IFNAME[4]="wlan0"
#IPADDR[4]=""
#NETMASK[4]=""
#USE_DHCP[4]="yes"
#DHCP_HOSTNAME[4]="icculus-wireless"
#DHCP_KEEPRESOLV[4]="yes"
#DHCP_KEEPNTP[4]="yes"
#DHCP_KEEPGW[4]="yes"
#DHCP_IPADDR[4]=""
#WLAN_ESSID[4]=BARRIER05
#WLAN_MODE[4]=Managed
##WLAN_RATE[4]="54M auto"
##WLAN_CHANNEL[4]="auto"
##WLAN_KEY[4]="D5AD1F04ACF048EC2D0B1C80C7"
##WLAN_IWPRIV[4]="AuthMode=WPAPSK EncrypType=TKIP WPAPSK=7B1ABEEB5D197741923ED26727569C365E31212096A0EAFAD563B268BAD01CAF TxRate=0"
#WLAN_WPA[4]="wpa_supplicant"
#WLAN_WPADRIVER[4]="ndiswrapper"

## Some examples of additional network parameters that you can use.
## Config information for wlan0:
#IFNAME[4]="wlan0"              # Use a different interface name nstead of
                                # the default 'eth4'
#HWADDR[4]="00:01:23:45:67:89"  # Overrule the card's hardware MAC address
#MTU[4]=""                      # The default MTU is 1500, but you might need
                                # 1360 when you use NAT'ed IPSec traffic.
#DHCP_KEEPRESOLV[4]="yes"       # If you dont want /etc/resolv.conf overwritten
#DHCP_KEEPNTP[4]="yes"          # If you don't want ntp.conf overwritten
#DHCP_KEEPGW[4]="yes"           # If you don't want the DHCP server to change
                                # your default gateway
#DHCP_IPADDR[4]=""              # Request a specific IP address from the DHCP
                                # server
#WLAN_ESSID[4]=DARKSTAR         # Here, you can override _any_ parameter
                                # defined in rc.wireless.conf, by prepending
                                # 'WLAN_' to the parameter's name. Useful for
                                # those with multiple wireless interfaces.
#WLAN_IWPRIV[4]="AuthMode=WPAPSK EncrypType=TKIP WPAPSK=thekey TxRate=0"
                                # Some drivers require a private ioctl to be
                                # set through the iwpriv command. If more than
                                # one is required, you can place them in the
                                # IWPRIV parameter (space-separated, see the
                                # example).


C'è qualche modulo non caricato ed è necessario per far riconoscere e funzionare eth0? Se la risposta è affermativa, quale?
Avatar utente
Kernel-Panic
Linux 1.0
Linux 1.0
 
Messaggi: 26
Iscritto il: mer dic 19, 2007 10:34
Slackware: 12.1
Distribuzione: ZW 6.0

Re: ZENWALK 6.0: problemi con eth0

Messaggioda luka64 » dom ott 25, 2009 21:51

dai un'occhiata qui:
http://tldp.org/HOWTO/Motorola-Surfboard-Modem/usb.html
poi fai risalire il sistema con il kernel originale zw, copiati l'lsmod e controlla le differenze.
Avatar utente
luka64
Linux 2.0
Linux 2.0
 
Messaggi: 175
Iscritto il: ven mag 22, 2009 9:47
Slackware: 12.2,9e
Kernel: 2.6.28.10
Desktop: xfce
Distribuzione: zw6.0

Re: ZENWALK 6.0: problemi con eth0

Messaggioda teox99 » dom ott 25, 2009 22:00

provato con
# ifconfig eth0 up
Avatar utente
teox99
Linux 2.6
Linux 2.6
 
Messaggi: 730
Iscritto il: ven lug 25, 2008 13:54
Località: Roma[Eur]
Slackware: 13.37
Desktop: KDE - Xfce

Re: ZENWALK 6.0: problemi con eth0

Messaggioda Kernel-Panic » dom ott 25, 2009 22:48

teox99 ha scritto:provato con
# ifconfig eth0 up


si, avevo provato, ma mi dava il seguente messaggio d'errore:

Codice: Seleziona tutto
eth0: error while getting interface flags. No such device
Avatar utente
Kernel-Panic
Linux 1.0
Linux 1.0
 
Messaggi: 26
Iscritto il: mer dic 19, 2007 10:34
Slackware: 12.1
Distribuzione: ZW 6.0

Re: ZENWALK 6.0: problemi con eth0

Messaggioda Kernel-Panic » dom ott 25, 2009 22:55

luka64 ha scritto:dai un'occhiata qui:
http://tldp.org/HOWTO/Motorola-Surfboard-Modem/usb.html
poi fai risalire il sistema con il kernel originale zw, copiati l'lsmod e controlla le differenze.


Ho aperto xkernelconfig con lo zenpanel. Tra i moduli non caricati ce n'era uno che si chiama cdc_ether (il nome è simile a quello presente nel link che mi hai postato). Così, da shell ho digitato:

Codice: Seleziona tutto
modprobe cdc_ether


e questo è l'output del comnando lsmod (le differenze rispetto al precedente ouput per lo stesso comando stanno tra i due "---"):

Codice: Seleziona tutto
Module                  Size  Used by
ipv6                  243508  16
pcmcia                 33772  0
pcmcia_core            32016  1 pcmcia
i915                  151464  2
drm                   137856  3 i915
i2c_algo_bit            5504  1 i915
iptable_mangle          2332  0
iptable_nat             4796  0
nf_nat                 16208  1 iptable_nat
nf_conntrack_ipv4      12520  3 iptable_nat,nf_nat
nf_conntrack           53844  3 iptable_nat,nf_nat,nf_conntrack_ipv4
nf_defrag_ipv4          1532  1 nf_conntrack_ipv4
iptable_filter          2268  0
ip_tables              10892  3 iptable_mangle,iptable_nat,iptable_filter
x_tables               13280  2 iptable_nat,ip_tables
fuse                   54008  6
3c59x                  39908  0
lp                      9316  0
sg                     24912  0
gspca_pac207            6428  0
gspca_main             21564  1 gspca_pac207
videodev               38688  1 gspca_main
v4l1_compat            13184  1 videodev
usb_storage            96096  1
cdc_acm                14752  0
---
cdc_ether               4732  0
usbnet                 13764  1 cdc_ether
mii                     4380  2 3c59x,usbnet
---
snd_intel8x0           28696  1
snd_ac97_codec        100128  1 snd_intel8x0
iTCO_wdt               10624  0
ac97_bus                1372  1 snd_ac97_codec
iTCO_vendor_support     2848  1 iTCO_wdt
rtc_cmos               10124  0
i2c_i801                8784  0
snd_pcm                68128  2 snd_intel8x0,snd_ac97_codec
intel_agp              25628  1
rtc_core               15992  1 rtc_cmos
dcdbas                  7068  0
ehci_hcd               35240  0
parport_pc             24036  1
i2c_core               20496  4 i915,drm,i2c_algo_bit,i2c_i801
thermal                15096  0
snd_timer              19108  1 snd_pcm
rtc_lib                 2332  1 rtc_core
parport                30700  2 lp,parport_pc
agpgart                29256  3 drm,intel_agp
processor              38600  1 thermal
psmouse                41676  0
snd                    50820  6 snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer
shpchp                 31888  0
thermal_sys            10756  2 thermal,processor
pcspkr                  2204  0
soundcore               5824  1 snd
serio_raw               5024  0
button                  5708  0
evdev                   9152  3
uhci_hcd               22284  0
snd_page_alloc          7972  2 snd_intel8x0,snd_pcm
hwmon                   2104  1 thermal_sys
reiserfs              230176  1



Fatto questo ho riavviato la rete, ma... Nisba, eth0 non è riconosciuta... :(
Avatar utente
Kernel-Panic
Linux 1.0
Linux 1.0
 
Messaggi: 26
Iscritto il: mer dic 19, 2007 10:34
Slackware: 12.1
Distribuzione: ZW 6.0

Re: ZENWALK 6.0: problemi con eth0

Messaggioda teox99 » dom ott 25, 2009 23:14

scusa forse mi sfugge...

che modello di scheda ethernet hai?
Avatar utente
teox99
Linux 2.6
Linux 2.6
 
Messaggi: 730
Iscritto il: ven lug 25, 2008 13:54
Località: Roma[Eur]
Slackware: 13.37
Desktop: KDE - Xfce

Re: ZENWALK 6.0: problemi con eth0

Messaggioda Kernel-Panic » dom ott 25, 2009 23:23

teox99 ha scritto:scusa forse mi sfugge...

che modello di scheda ethernet hai?


Ecco l'output del comando lspci

Codice: Seleziona tutto
00:00.0 Host bridge: Intel Corporation 82865G/PE/P DRAM Controller/Host-Hub Interface (rev 02)
00:02.0 VGA compatible controller: Intel Corporation 82865G Integrated Graphics Controller (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 (rev 02)
00:1d.3 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #4 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c2)
00:1f.0 ISA bridge: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus Controller (rev 02)
00:1f.5 Multimedia audio controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller (rev 02)
01:00.0 RAID bus controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02)
01:08.0 Ethernet controller: Intel Corporation 82562EZ 10/100 Ethernet Controller (rev 02)
Avatar utente
Kernel-Panic
Linux 1.0
Linux 1.0
 
Messaggi: 26
Iscritto il: mer dic 19, 2007 10:34
Slackware: 12.1
Distribuzione: ZW 6.0

Re: ZENWALK 6.0: problemi con eth0

Messaggioda luka64 » dom ott 25, 2009 23:48

@Kernel-Panic:dal tuo dmesg il sistema ti riconosce come eth0:
Codice: Seleziona tutto
eth0: register 'cdc_ether' at usb-0000:00:1d.0-1, CDC Ethernet Device, 00:08:5c:bc:5a:a5

ma in realtà si riferisce a una Broadcom usb.
Forse è questo l'inghippo?
@teox99 Offtopic: colgo l'occasione per segnalare che Zenwalk.it è di nuovo online :D
Avatar utente
luka64
Linux 2.0
Linux 2.0
 
Messaggi: 175
Iscritto il: ven mag 22, 2009 9:47
Slackware: 12.2,9e
Kernel: 2.6.28.10
Desktop: xfce
Distribuzione: zw6.0

Re: ZENWALK 6.0: problemi con eth0

Messaggioda Kernel-Panic » dom ott 25, 2009 23:55

luka64 ha scritto:@Kernel-Panic:dal tuo dmesg il sistema ti riconosce come eth0:
Codice: Seleziona tutto
eth0: register 'cdc_ether' at usb-0000:00:1d.0-1, CDC Ethernet Device, 00:08:5c:bc:5a:a5

ma in realtà si riferisce a una Broadcom usb.
Forse è questo l'inghippo?


Beh in effetti la scheda Ethernet, osservando l'output di lspci è la seguente:

Codice: Seleziona tutto
01:08.0 Ethernet controller: Intel Corporation 82562EZ 10/100 Ethernet Controller (rev 02)


Ma perchè allora mi riconosce una Broadcom USB? BOH?!? :-k

Un dubbio: mi conveniva installare il kernel huge piuttosto che quello generic? Oppure non cambia nulla in questo caso specifico?
Avatar utente
Kernel-Panic
Linux 1.0
Linux 1.0
 
Messaggi: 26
Iscritto il: mer dic 19, 2007 10:34
Slackware: 12.1
Distribuzione: ZW 6.0

Re: ZENWALK 6.0: problemi con eth0

Messaggioda luka64 » lun ott 26, 2009 0:11

Zenwalk e Slackware non sono la stessa cosa, se vuoi aggiornare
il kernel di zw ti suggerisco di scaricare la versione che ti interessa
da kernel.org e compilarla partendo dal .config originale.
Avatar utente
luka64
Linux 2.0
Linux 2.0
 
Messaggi: 175
Iscritto il: ven mag 22, 2009 9:47
Slackware: 12.2,9e
Kernel: 2.6.28.10
Desktop: xfce
Distribuzione: zw6.0

Re: ZENWALK 6.0: problemi con eth0

Messaggioda Kernel-Panic » lun ott 26, 2009 0:26

Probabilmente mi ha tratto in inganno il fatto che comunque Zenwalk è Slackware-based... C'era un file readme di Pat Volkerding che riportava la procedura che ho visto dal wiki di questo sito e ho usato quella...

Ad ogni modo, mi sa tanto che ripristinerò il kernel 2.6.28.7, dopodichè cercherò di fare quello che mi hai suggerito (anche se, come si intuisce dal mio nick non ho un buon rapporto con la compilazione dei kernel... :D )

Per ".config originale" intendi il ".config" del vecchio kernel?

Offtopic: Ottimo, ho appena visto che è stata rilasciata la versione 6.2 ;)
Avatar utente
Kernel-Panic
Linux 1.0
Linux 1.0
 
Messaggi: 26
Iscritto il: mer dic 19, 2007 10:34
Slackware: 12.1
Distribuzione: ZW 6.0

Re: ZENWALK 6.0: problemi con eth0

Messaggioda luka64 » lun ott 26, 2009 18:58

si, il .config del 2.6.28.7 'originale' zw. :thumbright:
Avatar utente
luka64
Linux 2.0
Linux 2.0
 
Messaggi: 175
Iscritto il: ven mag 22, 2009 9:47
Slackware: 12.2,9e
Kernel: 2.6.28.10
Desktop: xfce
Distribuzione: zw6.0


Torna a Porting Slackware

Chi c’è in linea

Visitano il forum: Nessuno e 2 ospiti