LTSP a1k ti sei arreso subito ??

Messaggio da **Luci0** » sab 18 nov 2006, 16:59

Ma accidenti ... proprio una scheda ISA .. !!!!
... ma per fare i test potevi scegliere qualcosa di Plug n' Play così é tutto più difficile ... é probabile che tu debba dare un opzione nel file lts.conf per caricare il modulo giusto dal momento che sei senza autoriconoscimento ... riesci ad eseguire il boot solo perché hai il corretto boot disk ...
Ma che scheda di rete hai ???
Comunque nel file lts.conf esiste l' opzione

Codice: Seleziona tutto

MODULE_01 through MODULE_10 
Upto 10 kernel modules can be loaded by using these configuration entries. The simplest way to load a module is to specify the module name only (e.g. rtl8129), which will be loaded by modprobe. Alternatively, the entire command line that you would enter when running insmod may be used instead. For example, the following lines would use insmod: 

         MODULE_01 = agpgart.o
         MODULE_02 = uart401.o
         MODULE_03 = "sb.o io=0x220 irq=5 dma=1"
         MODULE_04 = opl3.o


 Note that the full path to a module may need to be specified if using insmod (e.g. /lib/modules/2.6.17.3-ltsp-1/kernel/drivers/net/rtl1839.o), and that kernel 2.4 modules use a '.o' suffix whilst 2.6 modules use '.ko'.

comunque ecco il link ... http://wiki.ltsp.org/twiki/bin/view/Ltsp/LtsConf
fammi sapere ... a questo punto ci dovremmo essere

cointreau · Messaggio da **cointreau** » lun 20 nov 2006, 13:32

ho provato a caricare il modulo da lts.conf ma niente...
eppure secondo me non è questo, in quanto dopo aver caricato il kernel sembra che la sheda di rete sia riconosciuta

la scheda di rete è una 3com 3c509

provo a fare un tentativo dal mio pc e vedo se percaso da qui va

cointreau · Messaggio da **cointreau** » mer 22 nov 2006, 13:29

aggiornamento, ho provato a fare un boot da un'altra macchina che supporta il netboot dal bios; si pianta comunque ma sembra che la cosa vada un pò meglio, syslogd prende i messaggi dalla workstation:

Codice: Seleziona tutto

Nov 22 13:25:24 ws197.ltsp syslogd started: BusyBox v0.60.4 (2006.04.03-18:12+0000)
Nov 22 13:25:24 ws197.ltsp root: Linux version 2.6.16.1-ltsp-2 (root@bam) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu3)) #2 PREEMPT Sun Apr 16 22:21:48 EDT 2006
Nov 22 13:25:24 ws197.ltsp root: BIOS-provided physical RAM map:
Nov 22 13:25:24 ws197.ltsp root:  BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
Nov 22 13:25:24 ws197.ltsp root:  BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
Nov 22 13:25:24 ws197.ltsp root:  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
Nov 22 13:25:24 ws197.ltsp root:  BIOS-e820: 0000000000100000 - 000000001fef0000 (usable)
Nov 22 13:25:24 ws197.ltsp root:  BIOS-e820: 000000001fef0000 - 000000001feff000 (ACPI data)
Nov 22 13:25:24 ws197.ltsp root:  BIOS-e820: 000000001feff000 - 000000001ff00000 (ACPI NVS)
Nov 22 13:25:24 ws197.ltsp root:  BIOS-e820: 000000001ff00000 - 0000000020000000 (reserved)
Nov 22 13:25:24 ws197.ltsp root:  BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
Nov 22 13:25:24 ws197.ltsp root: 510MB LOWMEM available.
Nov 22 13:25:24 ws197.ltsp root: On node 0 totalpages: 130800
Nov 22 13:25:24 ws197.ltsp root:   DMA zone: 4096 pages, LIFO batch:0
Nov 22 13:25:24 ws197.ltsp root:   DMA32 zone: 0 pages, LIFO batch:0
Nov 22 13:25:24 ws197.ltsp root:   Normal zone: 126704 pages, LIFO batch:31
Nov 22 13:25:24 ws197.ltsp root:   HighMem zone: 0 pages, LIFO batch:0
Nov 22 13:25:24 ws197.ltsp root: DMI present.
Nov 22 13:25:24 ws197.ltsp root: ACPI: RSDP (v000 PTLTD                                 ) @ 0x000f6f70
Nov 22 13:25:24 ws197.ltsp root: ACPI: RSDT (v001 PTLTD  EGRSDT   0x01200000  LTP 0x00000000) @ 0x1fef5f33
Nov 22 13:25:24 ws197.ltsp root: ACPI: FADT (v001 ALI    EG533    0x01200000 PTL  0x000f4240) @ 0x1fefef64
Nov 22 13:25:24 ws197.ltsp root: ACPI: BOOT (v001 PTLTD  EGBFTBL$ 0x01200000  LTP 0x00000001) @ 0x1fefefd8
Nov 22 13:25:24 ws197.ltsp root: ACPI: DSDT (v001    ALI    EG533 0x01200000 MSFT 0x0100000d) @ 0x00000000
Nov 22 13:25:24 ws197.ltsp root: ACPI: PM-Timer IO Port: 0x8008
Nov 22 13:25:24 ws197.ltsp root: Allocating PCI resources starting at 30000000 (gap: 20000000:dffc0000)
Nov 22 13:25:24 ws197.ltsp root: Built 1 zonelists
Nov 22 13:25:24 ws197.ltsp root: Kernel command line: rw root=/dev/ram0 initrd=initramfs.gz BOOT_IMAGE=bzImage-2.6.16.1-ltsp-2 auto
Nov 22 13:25:24 ws197.ltsp root: Enabling fast FPU save and restore... done.
Nov 22 13:25:24 ws197.ltsp root: Enabling unmasked SIMD FPU exception support... done.
Nov 22 13:25:24 ws197.ltsp root: Initializing CPU#0
Nov 22 13:25:24 ws197.ltsp root: PID hash table entries: 2048 (order: 11, 32768 bytes)
Nov 22 13:25:24 ws197.ltsp root: Detected 1600.167 MHz processor.
Nov 22 13:25:24 ws197.ltsp root: Using pmtmr for high-res timesource
Nov 22 13:25:24 ws197.ltsp root: Console: colour VGA+ 80x25
Nov 22 13:25:24 ws197.ltsp root: Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Nov 22 13:25:24 ws197.ltsp root: Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Nov 22 13:25:24 ws197.ltsp root: Memory: 513588k/523200k available (2248k kernel code, 8940k reserved, 637k data, 164k init, 0k highmem)
Nov 22 13:25:24 ws197.ltsp root: Checking if this processor honours the WP bit even in supervisor mode... Ok.
Nov 22 13:25:24 ws197.ltsp root: Calibrating delay using timer specific routine.. 3205.50 BogoMIPS (lpj=6411004)
Nov 22 13:25:24 ws197.ltsp root: Security Framework v1.0.0 initialized
Nov 22 13:25:24 ws197.ltsp root: Mount-cache hash table entries: 512
Nov 22 13:25:24 ws197.ltsp root: CPU: After generic identify, caps: 3febf9ff 00000000 00000000 00000000 00000000 00000000 00000000
Nov 22 13:25:24 ws197.ltsp root: CPU: After vendor identify, caps: 3febf9ff 00000000 00000000 00000000 00000000 00000000 00000000
Nov 22 13:25:24 ws197.ltsp root: CPU: Trace cache: 12K uops, L1 D cache: 8K
Nov 22 13:25:24 ws197.ltsp root: CPU: L2 cache: 512K
Nov 22 13:25:24 ws197.ltsp root: CPU: After all inits, caps: 3febf9ff 00000000 00000000 00000080 00000000 00000000 00000000
Nov 22 13:25:24 ws197.ltsp root: Intel machine check architecture supported.
Nov 22 13:25:24 ws197.ltsp root: Intel machine check reporting enabled on CPU#0.
Nov 22 13:25:24 ws197.ltsp root: CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
Nov 22 13:25:24 ws197.ltsp root: CPU: Intel(R) Pentium(R) 4 Mobile CPU 1.60GHz stepping 04
Nov 22 13:25:24 ws197.ltsp root: Checking 'hlt' instruction... OK.
Nov 22 13:25:24 ws197.ltsp root: ACPI: setting ELCR to 0200 (from 0e00)
Nov 22 13:25:24 ws197.ltsp root: checking if image is initramfs... it is
Nov 22 13:25:24 ws197.ltsp root: Freeing initrd memory: 1140k freed
Nov 22 13:25:24 ws197.ltsp root: NET: Registered protocol family 16
Nov 22 13:25:24 ws197.ltsp root: ACPI: bus type pci registered
Nov 22 13:25:24 ws197.ltsp root: PCI: PCI BIOS revision 2.10 entry at 0xfd89b, last bus=1
Nov 22 13:25:24 ws197.ltsp root: PCI: Using configuration type 1
Nov 22 13:25:24 ws197.ltsp root: ACPI: Subsystem revision 20060127
Nov 22 13:25:24 ws197.ltsp root: ACPI: Interpreter enabled
Nov 22 13:25:24 ws197.ltsp root: ACPI: Using PIC for interrupt routing
Nov 22 13:25:24 ws197.ltsp root: ACPI: PCI Root Bridge [PCI0] (0000:00)
Nov 22 13:25:24 ws197.ltsp root: PCI: Probing PCI hardware (bus 00)
Nov 22 13:25:24 ws197.ltsp root: PCI quirk: region 8000-803f claimed by ali7101 ACPI
Nov 22 13:25:24 ws197.ltsp root: PCI quirk: region 8040-805f claimed by ali7101 SMB
Nov 22 13:25:24 ws197.ltsp root: Boot video device is 0000:01:00.0
Nov 22 13:25:24 ws197.ltsp root: ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
Nov 22 13:25:24 ws197.ltsp root: ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 11 12) *0, disabled.
Nov 22 13:25:24 ws197.ltsp root: ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *11 12)
Nov 22 13:25:24 ws197.ltsp root: ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *10 12)
Nov 22 13:25:24 ws197.ltsp root: ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 10 12) *0, disabled.
Nov 22 13:25:24 ws197.ltsp root: ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 12) *0, disabled.
Nov 22 13:25:24 ws197.ltsp root: ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 12) *0, disabled.
Nov 22 13:25:24 ws197.ltsp root: ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 6 7 10 12) *0, disabled.
Nov 22 13:25:24 ws197.ltsp root: ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 11 12) *0, disabled.
Nov 22 13:25:24 ws197.ltsp root: ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 6 7 10 12) *9
Nov 22 13:25:24 ws197.ltsp root: ACPI: Embedded Controller [EC0] (gpe 24) interrupt mode.
Nov 22 13:25:24 ws197.ltsp root: ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
Nov 22 13:25:24 ws197.ltsp root: ACPI: Power Resource [PFNL] (off)
Nov 22 13:25:24 ws197.ltsp root: Linux Plug and Play Support v0.97 (c) Adam Belay
Nov 22 13:25:24 ws197.ltsp root: pnp: PnP ACPI init
Nov 22 13:25:24 ws197.ltsp root: pnp: PnP ACPI: found 12 devices
Nov 22 13:25:24 ws197.ltsp root: PnPBIOS: Disabled by ACPI PNP
Nov 22 13:25:24 ws197.ltsp root: PCI: Using ACPI for IRQ routing
Nov 22 13:25:24 ws197.ltsp root: PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
Nov 22 13:25:24 ws197.ltsp root: pnp: 00:07: ioport range 0x3810-0x381f has been reserved
Nov 22 13:25:24 ws197.ltsp root: pnp: 00:07: ioport range 0x4d0-0x4d1 has been reserved
Nov 22 13:25:24 ws197.ltsp root: pnp: 00:07: ioport range 0x8000-0x805f could not be reserved
Nov 22 13:25:24 ws197.ltsp root: pnp: 00:07: ioport range 0x4d6-0x4d6 has been reserved
Nov 22 13:25:24 ws197.ltsp root: PCI: Bridge: 0000:00:01.0
Nov 22 13:25:24 ws197.ltsp root:   IO window: 9000-9fff
Nov 22 13:25:24 ws197.ltsp root:   MEM window: e0100000-e01fffff
Nov 22 13:25:24 ws197.ltsp root:   PREFETCH window: e8000000-efffffff
Nov 22 13:25:24 ws197.ltsp root: PCI: Bus 2, cardbus bridge: 0000:00:0a.0
Nov 22 13:25:24 ws197.ltsp root:   IO window: 00001c00-00001cff
Nov 22 13:25:24 ws197.ltsp root:   IO window: 00002000-000020ff
Nov 22 13:25:24 ws197.ltsp root:   PREFETCH window: 30000000-31ffffff
Nov 22 13:25:24 ws197.ltsp root:   MEM window: 32000000-33ffffff
Nov 22 13:25:24 ws197.ltsp root: PCI: Setting latency timer of device 0000:00:01.0 to 64
Nov 22 13:25:24 ws197.ltsp root: ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
Nov 22 13:25:24 ws197.ltsp root: PCI: setting IRQ 11 as level-triggered
Nov 22 13:25:24 ws197.ltsp root: ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
Nov 22 13:25:24 ws197.ltsp root: PCI: Setting latency timer of device 0000:00:0a.0 to 64
Nov 22 13:25:24 ws197.ltsp root: Simple Boot Flag at 0x38 set to 0x1
Nov 22 13:25:24 ws197.ltsp root: Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Nov 22 13:25:24 ws197.ltsp root: Initializing Cryptographic API
Nov 22 13:25:24 ws197.ltsp root: io scheduler noop registered
Nov 22 13:25:24 ws197.ltsp root: io scheduler anticipatory registered (default)
Nov 22 13:25:24 ws197.ltsp root: io scheduler deadline registered
Nov 22 13:25:24 ws197.ltsp root: io scheduler cfq registered
Nov 22 13:25:24 ws197.ltsp root: Activating ISA DMA hang workarounds.
Nov 22 13:25:24 ws197.ltsp root: isapnp: Scanning for PnP cards...
Nov 22 13:25:24 ws197.ltsp root: isapnp: No Plug & Play device found
Nov 22 13:25:24 ws197.ltsp root: Linux agpgart interface v0.101 (c) Dave Jones
Nov 22 13:25:24 ws197.ltsp root: [drm] Initialized drm 1.0.1 20051102
Nov 22 13:25:24 ws197.ltsp root: intelfb: Framebuffer driver for Intel(R) 830M/845G/852GM/855GM/865G/915G/915GM chipsets
Nov 22 13:25:24 ws197.ltsp root: intelfb: Version 0.9.2
Nov 22 13:25:24 ws197.ltsp root: PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
Nov 22 13:25:24 ws197.ltsp root: serio: i8042 AUX port at 0x60,0x64 irq 12
Nov 22 13:25:24 ws197.ltsp root: serio: i8042 KBD port at 0x60,0x64 irq 1
Nov 22 13:25:24 ws197.ltsp root: Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
Nov 22 13:25:24 ws197.ltsp root: serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Nov 22 13:25:24 ws197.ltsp root: serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Nov 22 13:25:24 ws197.ltsp root: 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Nov 22 13:25:24 ws197.ltsp root: RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Nov 22 13:25:24 ws197.ltsp root: mice: PS/2 mouse device common for all mice
Nov 22 13:25:24 ws197.ltsp root: NET: Registered protocol family 2
Nov 22 13:25:24 ws197.ltsp root: IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
Nov 22 13:25:24 ws197.ltsp root: TCP established hash table entries: 16384 (order: 4, 65536 bytes)
Nov 22 13:25:24 ws197.ltsp root: TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
Nov 22 13:25:24 ws197.ltsp root: TCP: Hash tables configured (established 16384 bind 16384)
Nov 22 13:25:24 ws197.ltsp root: TCP reno registered
Nov 22 13:25:24 ws197.ltsp root: TCP bic registered
Nov 22 13:25:24 ws197.ltsp root: NET: Registered protocol family 1
Nov 22 13:25:24 ws197.ltsp root: NET: Registered protocol family 17
Nov 22 13:25:24 ws197.ltsp root: Using IPI Shortcut mode
Nov 22 13:25:24 ws197.ltsp root: ACPI wakeup devices:
Nov 22 13:25:24 ws197.ltsp root: SLPB  LID  LAN  USB
Nov 22 13:25:24 ws197.ltsp root: ACPI: (supports S0 S1 S3 S4 S5)
Nov 22 13:25:24 ws197.ltsp root: Freeing unused kernel memory: 164k freed
Nov 22 13:25:24 ws197.ltsp root: input: AT Translated Set 2 keyboard as /class/input/input0
Nov 22 13:25:24 ws197.ltsp root: 8139too Fast Ethernet driver 0.9.27
Nov 22 13:25:24 ws197.ltsp root: ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
Nov 22 13:25:24 ws197.ltsp root: PCI: setting IRQ 10 as level-triggered
Nov 22 13:25:24 ws197.ltsp root: ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
Nov 22 13:25:24 ws197.ltsp root: eth0: RealTek RTL8139 at 0x1800, 00:e0:4c:0a:30:91, IRQ 10
Nov 22 13:25:24 ws197.ltsp root: eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
Nov 22 13:25:24 ws197.ltsp root: eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Nov 22 13:25:24 ws197.ltsp root: Synaptics Touchpad, model: 1, fw: 5.8, id: 0x9b48b1, caps: 0x88479b/0x0
Nov 22 13:25:24 ws197.ltsp root: serio: Synaptics pass-through port at isa0060/serio1/input0
Nov 22 13:25:24 ws197.ltsp root: input: SynPS/2 Synaptics TouchPad as /class/input/input1
Nov 22 13:25:24 ws197.ltsp root: usbcore: registered new driver usbfs
Nov 22 13:25:24 ws197.ltsp root: usbcore: registered new driver hub
Nov 22 13:25:24 ws197.ltsp root: USB Universal Host Controller Interface driver v2.3
Nov 22 13:25:24 ws197.ltsp root: ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
Nov 22 13:25:24 ws197.ltsp root: ACPI: PCI Interrupt Link [LNKU] enabled at IRQ 10
Nov 22 13:25:24 ws197.ltsp root: ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKU] -> GSI 10 (level, low) -> IRQ 10
Nov 22 13:25:24 ws197.ltsp root: ohci_hcd 0000:00:02.0: OHCI Host Controller
Nov 22 13:25:24 ws197.ltsp root: ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
Nov 22 13:25:24 ws197.ltsp root: ohci_hcd 0000:00:02.0: irq 10, io mem 0xe0000000
Nov 22 13:25:24 ws197.ltsp root: usb usb1: configuration #1 chosen from 1 choice
Nov 22 13:25:24 ws197.ltsp root: hub 1-0:1.0: USB hub found
Nov 22 13:25:24 ws197.ltsp root: hub 1-0:1.0: 2 ports detected
Nov 22 13:25:24 ws197.ltsp root: usbcore: registered new driver usbmouse
Nov 22 13:25:24 ws197.ltsp root: drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
Nov 22 13:25:24 ws197.ltsp root: usbcore: registered new driver usbkbd
Nov 22 13:25:24 ws197.ltsp root: drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver
Nov 22 13:25:24 ws197.ltsp init: Entering runlevel: 5

a questo punto, la workstation mi dice che switcha al runlevel 5 e si blocca lì

spero di essere a buon punto

Messaggio da **Luci0** » gio 23 nov 2006, 9:02

Ciao cointreau...
sembra che qualcosa si sia mosso ma é probabile che tu debba rifinire l' installazione .... se non vedi andare lo schermo in modalità grafica é probabile che l'autoconfigurazione della scheda non vada a buon fine ...
Prova a modificare il file lts..conf in modo da mettere il driver Vesa e avere una
shell ... se non va ancora prova a postarlo..

Codice: Seleziona tutto

-----------------------
#
# Copyright (c) 2003 by James A. McQuillan (McQuillan Systems, LLC)
#
# This software is licensed under the Gnu General Public License.
# The full text of which can be found at http://www.LTSP.org/license.txt
#
#
# Config file for the Linux Terminal Server Project (www.ltsp.org)
#

[Default]
        SERVER             = 192.168.0.254
#       XSERVER            = auto   
        XSERVER            = vesa
# modifica N.1               ^^^^^
        X_MOUSE_PROTOCOL   = "PS/2"
        X_MOUSE_DEVICE     = "/dev/psaux"
        X_MOUSE_RESOLUTION = 400
        X_MOUSE_BUTTONS    = 3
        USE_XFS            = N
        SCREEN_01          = startx
        SCREEN_02          = shell
# modifica N.2               ^^^^^
------------------

Ciao ..

cointreau · Messaggio da **cointreau** » gio 23 nov 2006, 21:35

\o/ il portatile funzia

ora mi rimane da far funzionare i pc vetusti

grazie Luci0

Messaggio da **Luci0** » ven 24 nov 2006, 1:35

Ottimo lavoro ...
Adesso per la 3com 3c509 dai un occhio su http://wiki.ltsp.org/twiki/bin/view/Ltsp/NetworkCards

... visto che era più difficile !!! Ciao

cointreau · Messaggio da **cointreau** » ven 24 nov 2006, 12:12

dunque, ho provato per curiosità eduknoppix che ha già tutto pronto per ltsp e il pc vetusto parte senza nessun problema...

allora mi sono chiesto... "se da qui parte senza modifiche da driver esterni.. perchè non dovrebbe anche dalla mia slack?"

ho provato a dare un'occhiata ai file di conf ma è un casino estremo... è tutto organizzato diversamente...

...e io che cercavo una scappatoia per non usare quella roba dal sito 3com...

Messaggio da **Luci0** » ven 24 nov 2006, 12:36

... la pappa pronta va bene se si ha fretta ...

non puoi lasciare perdere quando sei al 95% del lavoro !!!

... ovvero ti sei arreso !!!

cointreau · Messaggio da **cointreau** » ven 24 nov 2006, 14:48

ahah nono

sto vedendo come fare

sarebbe da pazzi fermarsi ora considerando il fastidio che ti ho dato! e che DEVO far funzionare anche le schede isa =)

cointreau · Messaggio da **cointreau** » ven 24 nov 2006, 17:14

aggiornamento:

credo di aver quasi risolto leggendo:

http://wiki.ltsp.org/twiki/bin/view/Lts ... responding
http://wiki.ltsp.org/twiki/bin/view/Ltsp/KernelOptions

Messaggio da **Luci0** » sab 25 nov 2006, 11:29

Ciao ...
Ma quanti sono i PC con le 3com ??
Per motivi di prestazioni ti consiglio vivamente di sostituire le schede a 10Mbit ISA con delle schede PCI a 100 Mbit ... vanno benissimo le comuni Realtek 8139x PCI

... così con poca spesa il computer ha un' altra resa ..

cointreau · Messaggio da **cointreau** » sab 25 nov 2006, 11:49

eheheh le prove le faccio a casa con un p200 alternando le schede di rete per provare

per poi mettere in pratica il tutto con una decina di 486 che non hanno slot pci tutti forniti della stessa medesima maledetta scheda che tralatro mi freeza il server

ho appena provato a usare tcp invece di udp.. ma il tutto freeza prima :P in giornata provo l'ultility sul sito 3com che consigliano anche nella mailing list di ltsp

sto anche provando [senza risultati per ora] a cercare come e dove configura tutto eduknoppix

appena ho qualche novità posto qui