S3 Graphics ProSavageDDR DRIVER

n3tfr33 · Messaggio da **n3tfr33** » mer 12 lug 2006, 13:48

Lo so che può sembrare una domanda stupida ma dove trovo la versione del kernel e di Xorg...scusa ma mi stò affaciando adesso al mondo di Linux

Messaggio da **phobos3576** » gio 13 lug 2006, 2:15

La versione del kernel che stai usando la puoi ottenere aprendo una console e digitando il comando:

uname -r

La versione di Xorg che stai usando è indicata nella prima riga del file /var/log/Xorg.0.log.

n3tfr33 · Messaggio da **n3tfr33** » gio 13 lug 2006, 19:17

Allora mi sa che abbiamo trovato il problema: kernerl 2.6.15.6 e xorg 6.9.0.
Che devo fare???
Reinstallare tutto o posso aggiornare il kernel???

Messaggio da **phobos3576** » ven 14 lug 2006, 1:40

Non c'è bisogno di reinstallare tutto; devi solo aggiornare il kernel e configurarlo a dovere abilitando gli opportuni moduli (m).

Presumo che la tua scheda video sia connessa al bus PCI tramite un bridge AGP/PCI della VIA.
Da una console prova a dare il comando /sbin/lspci e controlla la linea in cui si parla di AGP

Supponendo che sia VIA, nella sezione AGP del kernel devi selezionare:

Codice: Seleziona tutto

CONFIG_AGP=m
CONFIG_AGP_VIA=m

Nella sezione DRM devi selezionare

Codice: Seleziona tutto

CONFIG_DRM=m
CONFIG_DRM_SAVAGE=m

Controlla attentamente anche le altre opzioni relative alle schede savage; ad esempio, nella sezione I2C Hardware Bus support dovresti selezionare:

Codice: Seleziona tutto

CONFIG_I2C_PROSAVAGE=m

Se non sei molto esperto nella ricompilazione del kernel, consulta la migliore guida del mondo che puoi trovare qui su Slacky.it all'indirizzo:

http://www.slacky.it/tutorial/kernel/co ... ernel.html

n3tfr33 · Messaggio da **n3tfr33** » ven 14 lug 2006, 14:36

Perfetto...aiutami solo a decidere quale versione di kernel installare...non so le differenze tra quelli che trovo in ftp://ftp.slackware.com/pub/slackware/s ... t/kernels/...penso che sia giusto prenderli da qui...grazie

Messaggio da **phobos3576** » ven 14 lug 2006, 16:03

Già che ci sei, scarica il codice sorgente dell'ultima versione che trovi sul sito ufficiale http://www.kernel.org/

Nella riga The latest stable version of the Linux kernel is: clicca sulla lettera F (che indica la versione full).

Prima di buttarti nella ricompilazione del kernel, raccogli il maggior numero possibile di informazioni sul tuo hardware; se hai Windows in un'altra partizione del tuo notebook, puoi eseguire Microsoft System Information che ti dà tutti i dettagli di cui hai bisogno!

n3tfr33 · Messaggio da **n3tfr33** » lun 17 lug 2006, 15:31

Ho aggiornato il kernel attivando tutti i moduli relativi al mio hardware e funziona perfettamente ma l'accelerazione non vuole saperne di attivarsi...altre idee??? (comunque con il nuovo kernel l'O.S. è decisamente più veloce...almeno una cosa giusta mi è uscita...hi hi hi). Grazie

Messaggio da **phobos3576** » lun 17 lug 2006, 17:02

Pure nel mio caso, il passaggio dal 2.6.16.x al 2.6.17.x ha prodotto un notevole aumento delle prestazioni (che erano già ottime anche prima); la ricompilazione del kernel da codice sorgente permette di ottenere risultati che non sono certo raggiungibili con i kernel precompilati.

Per quanto riguarda l'accelerazione hardware, come ti ho già detto, mi sembra impossibile che nel file /var/log/Xorg.0.log non ci sia nessun messaggio di errore; nella parte finale di tale file, dovresti trovare righe del tipo:

Codice: Seleziona tutto

(==) MGA(0): Write-combining range (0xea000000,0x2000000)
(II) MGA(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(--) MGA(0): 16 DWORD fifo
(==) MGA(0): Default visual is TrueColor
(II) MGA(0): [drm] bpp: 32 depth: 24
(II) MGA(0): [drm] Sarea 2200+664: 2864
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 10, (OK)
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 10, (OK)
drmOpenByBusid: Searching for BusID pci:0000:01:05.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 10, (OK)
drmOpenByBusid: drmOpenMinor returns 10
drmOpenByBusid: drmGetBusid reports pci:0000:01:05.0
(II) MGA(0): [drm] DRM interface version 1.2
(II) MGA(0): [drm] created "mga" driver at busid "pci:0000:01:05.0"
(II) MGA(0): [drm] added 8192 byte SAREA at 0xe0a50000
(II) MGA(0): [drm] mapped SAREA 0xe0a50000 to 0xb512f000
(II) MGA(0): [drm] framebuffer handle = 0xea000000
(II) MGA(0): [drm] added 1 reserved context for kernel
(II) MGA(0): [dri] visual configs initialized
(II) MGA(0): Memory manager initialized to (0,0) (1024,2303)
(II) MGA(0): Largest offscreen area available: 1024 x 1535
(II) MGA(0): Reserved back buffer at offset 0x900000
(II) MGA(0): Reserved depth buffer at offset 0xc00000
(II) MGA(0): Reserved 17408 kb for textures at offset 0xf00000
(II) MGA(0): Using XFree86 Acceleration Architecture (XAA)
	Screen to screen bit blits
	Solid filled rectangles
	Solid filled trapezoids
	8x8 mono pattern filled rectangles
	8x8 mono pattern filled trapezoids
	Indirect CPU to Screen color expansion
	Screen to Screen color expansion
	Solid Lines
	Dashed Lines
	Scanline Image Writes
	Offscreen Pixmaps
	Driver provided FillMono8x8PatternRects replacement
	Setting up tile and stipple cache:
		32 128x128 slots
		14 256x256 slots
(==) MGA(0): Backing store disabled
(==) MGA(0): Silken mouse enabled
(II) MGA(0): Using overlay video
(II) MGA(0): X context handle = 0x1
(II) MGA(0): [drm] installed DRM signal handler
(II) MGA(0): [DRI] installation complete
(II) MGA(0): [drm] Mapped 128 DMA buffers
(II) MGA(0): [drm] dma control initialized, using IRQ 10
(II) MGA(0): Direct rendering enabled

(L'esempio è relativo alla mia Matrox Millennium G400)

Se il DRI non viene attivato, dovresti trovare una sfilza di messaggi di errore.
In ogni caso, anche senza i messaggi di errore, il file di log dovrebbe indicare per quale motivo il DRI non è stato attivato.

n3tfr33 · Messaggio da **n3tfr33** » mar 18 lug 2006, 1:41

Ho controllato tutto il file e mi sembra come il tuo, anzi dice che l'accellerazione è stata caricata...ma da glxinfo la Direct Redering è ancora a No.

Adesso ti posto tutto il file:

_XSERVTransSocketOpenCOTSServer: Unable to open socket for inet6
_XSERVTransOpen: transport open failed for inet6/slax:0
_XSERVTransMakeAllCOTSServerListeners: failed to open listener for inet6

X Window System Version 6.9.0
Release Date: 21 December 2005
X Protocol Version 11, Revision 0, Release 6.9
Build Operating System: Linux 2.6.14.6 i686 [ELF]
Current Operating System: Linux slax 2.6.15.6 #1 SMP Fri Mar 24 16:46:23 GMT 2006 i686
Build Date: 14 January 2006
Before reporting problems, check http://wiki.X.Org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Tue Jul 18 01:32:57 2006
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "Simple Layout"
(**) |-->Screen "Screen 1" (0)
(**) | |-->Monitor "My Monitor"
(**) | |-->Device "VESA Framebuffer"
(**) |-->Input Device "Mouse1"
(**) |-->Input Device "Keyboard1"
(**) FontPath set to "/usr/X11R6/lib/X11/fonts/local/,/usr/X11R6/lib/X11/fonts/misc/,/usr/X11R6/lib/X11/fonts/75dpi/:unscaled,/usr/X11R6/lib/X11/fonts/100dpi/:unscaled,/usr/X11R6/lib/X11/fonts/Type1/,/usr/X11R6/lib/X11/fonts/CID/,/usr/X11R6/lib/X11/fonts/Speedo/,/usr/X11R6/lib/X11/fonts/75dpi/,/usr/X11R6/lib/X11/fonts/100dpi/,/usr/X11R6/lib/X11/fonts/cyrillic/"
(**) RgbPath set to "/usr/X11R6/lib/X11/rgb"
(==) ModulePath set to "/usr/X11R6/lib/modules"
(II) Open ACPI successful (/var/run/acpid.socket)
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.2
X.Org Video Driver: 0.8
X.Org XInput driver : 0.5
X.Org Server Extension : 0.2
X.Org Font Renderer : 0.4
(II) Loader running on linux
(II) LoadModule: "bitmap"
(II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.so
(II) Module bitmap: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.4
(II) Loading font Bitmap
(II) LoadModule: "pcidata"
(II) Loading /usr/X11R6/lib/modules/libpcidata.so
(II) Module pcidata: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.0
ABI class: X.Org Video Driver, version 0.8
(--) using VT number 7

(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 1106,3156 card 1631,e004 rev 00 class 06,00,00 hdr 00
(II) PCI: 00:01:0: chip 1106,b091 card 0000,0000 rev 00 class 06,04,00 hdr 01
(II) PCI: 00:09:0: chip 1524,1411 card 1800,0000 rev 01 class 06,07,00 hdr 82
(II) PCI: 00:10:0: chip 1106,3038 card 1631,e004 rev 80 class 0c,03,00 hdr 80
(II) PCI: 00:10:1: chip 1106,3038 card 1631,e004 rev 80 class 0c,03,00 hdr 80
(II) PCI: 00:10:3: chip 1106,3104 card 1631,e004 rev 82 class 0c,03,20 hdr 00
(II) PCI: 00:11:0: chip 1106,3177 card 1631,e004 rev 00 class 06,01,00 hdr 80
(II) PCI: 00:11:1: chip 1106,0571 card 1631,e004 rev 06 class 01,01,8a hdr 00
(II) PCI: 00:11:5: chip 1106,3059 card 1631,e004 rev 50 class 04,01,00 hdr 00
(II) PCI: 00:11:6: chip 1106,3068 card 1631,e004 rev 80 class 07,80,00 hdr 00
(II) PCI: 00:12:0: chip 1106,3065 card 1631,e004 rev 74 class 02,00,00 hdr 00
(II) PCI: 01:00:0: chip 5333,8d04 card 1631,e004 rev 00 class 03,00,00 hdr 00
(II) PCI: End of PCI scan
(II) Host-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (0,0,2), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 0 I/O range:
[0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX
(II) Bus 0 non-prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX
(II) Bus 0 prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX
(II) PCI-to-PCI bridge:
(II) Bus 1: bridge is at (0:1:0), (0,1,1), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 1 I/O range:
[0] -1 0 0x0000c000 - 0x0000dfff (0x2000) IX
(II) Bus 1 non-prefetchable memory range:
[0] -1 0 0xe0000000 - 0xefffffff (0x10000000) MX
(II) Bus 1 prefetchable memory range:
[0] -1 0 0x90000000 - 0x9fffffff (0x10000000) MX
(II) PCI-to-CardBus bridge:
(II) Bus 2: bridge is at (0:9:0), (0,2,5), BCTRL: 0x05c0 (VGA_EN is cleared)
(II) Bus 2 I/O range:
[0] -1 0 0x00001800 - 0x000018ff (0x100) IX
[1] -1 0 0x00001c00 - 0x00001cff (0x100) IX
(II) Bus 2 non-prefetchable memory range:
[0] -1 0 0x12000000 - 0x13ffffff (0x2000000) MX
(II) Bus 2 prefetchable memory range:
[0] -1 0 0x10000000 - 0x11ffffff (0x2000000) MX
(II) PCI-to-ISA bridge:
(II) Bus -1: bridge is at (0:17:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set)
(--) PCI:*(1:0:0) S3 Inc. VT8375 [ProSavage8 KM266/KL266] rev 0, Mem @ 0xe0000000/19, 0x90000000/27, BIOS @ 0x000c0000/16
(II) Addressable bus resource ranges are
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
[1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) OS-reported resource ranges:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) PCI Memory resource overlap reduced 0xa0000000 from 0xa3ffffff to 0x9fffffff
(II) Active PCI resource ranges:
[0] -1 0 0xf0000100 - 0xf00001ff (0x100) MX[B]
[1] -1 0 0xf0000000 - 0xf00000ff (0x100) MX[B]
[2] -1 0 0xa0000000 - 0x9fffffff (0x0) MX[B]O
[3] -1 0 0x98000000 - 0x9800ffff (0x10000) MX[B](B)
[4] -1 0 0x90000000 - 0x97ffffff (0x8000000) MX[B](B)
[5] -1 0 0xe0000000 - 0xe007ffff (0x80000) MX[B](B)
[6] -1 0 0x0000e300 - 0x0000e3ff (0x100) IX[B]
[7] -1 0 0x0000e200 - 0x0000e2ff (0x100) IX[B]
[8] -1 0 0x0000e100 - 0x0000e1ff (0x100) IX[B]
[9] -1 0 0x00001100 - 0x0000110f (0x10) IX[B]
[10] -1 0 0x00001300 - 0x0000131f (0x20) IX[B]
[11] -1 0 0x00001200 - 0x0000121f (0x20) IX[B]
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0 0xf0000100 - 0xf00001ff (0x100) MX[B]
[1] -1 0 0xf0000000 - 0xf00000ff (0x100) MX[B]
[2] -1 0 0xa0000000 - 0x9fffffff (0x0) MX[B]O
[3] -1 0 0x98000000 - 0x9800ffff (0x10000) MX[B](B)
[4] -1 0 0x90000000 - 0x97ffffff (0x8000000) MX[B](B)
[5] -1 0 0xe0000000 - 0xe007ffff (0x80000) MX[B](B)
[6] -1 0 0x0000e300 - 0x0000e3ff (0x100) IX[B]
[7] -1 0 0x0000e200 - 0x0000e2ff (0x100) IX[B]
[8] -1 0 0x0000e100 - 0x0000e1ff (0x100) IX[B]
[9] -1 0 0x00001100 - 0x0000110f (0x10) IX[B]
[10] -1 0 0x00001300 - 0x0000131f (0x20) IX[B]
[11] -1 0 0x00001200 - 0x0000121f (0x20) IX[B]
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) All system resource ranges:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xf0000100 - 0xf00001ff (0x100) MX[B]
[6] -1 0 0xf0000000 - 0xf00000ff (0x100) MX[B]
[7] -1 0 0xa0000000 - 0x9fffffff (0x0) MX[B]O
[8] -1 0 0x98000000 - 0x9800ffff (0x10000) MX[B](B)
[9] -1 0 0x90000000 - 0x97ffffff (0x8000000) MX[B](B)
[10] -1 0 0xe0000000 - 0xe007ffff (0x80000) MX[B](B)
[11] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[12] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[13] -1 0 0x0000e300 - 0x0000e3ff (0x100) IX[B]
[14] -1 0 0x0000e200 - 0x0000e2ff (0x100) IX[B]
[15] -1 0 0x0000e100 - 0x0000e1ff (0x100) IX[B]
[16] -1 0 0x00001100 - 0x0000110f (0x10) IX[B]
[17] -1 0 0x00001300 - 0x0000131f (0x20) IX[B]
[18] -1 0 0x00001200 - 0x0000121f (0x20) IX[B]
(II) LoadModule: "dbe"
(II) Loading /usr/X11R6/lib/modules/extensions/libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "v4l"
(II) Loading /usr/X11R6/lib/modules/drivers/v4l_drv.so
(II) Module v4l: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 0.0.1
ABI class: X.Org Video Driver, version 0.8
(II) LoadModule: "extmod"
(II) Loading /usr/X11R6/lib/modules/extensions/libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "type1"
(II) Loading /usr/X11R6/lib/modules/fonts/libtype1.so
(II) Module type1: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.2
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.4
(II) Loading font Type1
(II) Loading font CID
(II) LoadModule: "freetype"
(II) Loading /usr/X11R6/lib/modules/fonts/libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
compiled for 6.9.0, module version = 2.1.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.4
(II) Loading font FreeType
(II) LoadModule: "glx"
(II) Loading /usr/X11R6/lib/modules/extensions/libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.2
(II) Loading sub module "GLcore"
(II) LoadModule: "GLcore"
(II) Loading /usr/X11R6/lib/modules/extensions/libGLcore.so
(II) Module GLcore: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension GLX
(II) LoadModule: "dri"
(II) Loading /usr/X11R6/lib/modules/extensions/libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.2
(II) Loading sub module "drm"
(II) LoadModule: "drm"
(II) Loading /usr/X11R6/lib/modules/linux/libdrm.so
(II) Module drm: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension XFree86-DRI
(II) LoadModule: "savage"
(II) Loading /usr/X11R6/lib/modules/drivers/savage_drv.so
(II) Module savage: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 2.0.2
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 0.8
(II) LoadModule: "mouse"
(II) Loading /usr/X11R6/lib/modules/input/mouse_drv.so
(II) Module mouse: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.3
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.5
(II) LoadModule: "kbd"
(II) Loading /usr/X11R6/lib/modules/input/kbd_drv.so
(II) Module kbd: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.1
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.5
(II) v4l driver for Video4Linux
(II) SAVAGE: driver (version 2.0.2) for S3 Savage chipsets: Savage4,
Savage3D, Savage3D-MV, Savage2000, Savage/MX-MV, Savage/MX,
Savage/IX-MV, Savage/IX, ProSavage PM133, ProSavage KM133,
Twister PN133, Twister KN133, SuperSavage/MX 128, SuperSavage/MX 64,
SuperSavage/MX 64C, SuperSavage/IX 128, SuperSavage/IX 128,
SuperSavage/IX 64, SuperSavage/IX 64, SuperSavage/IXC 64,
SuperSavage/IXC 64, ProSavage DDR, ProSavage DDR-K
(II) Primary Device is: PCI 01:00:0
(--) Assigning device section with no busID to primary device
(--) Chipset ProSavageDDR found
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xf0000100 - 0xf00001ff (0x100) MX[B]
[6] -1 0 0xf0000000 - 0xf00000ff (0x100) MX[B]
[7] -1 0 0xa0000000 - 0x9fffffff (0x0) MX[B]O
[8] -1 0 0x98000000 - 0x9800ffff (0x10000) MX[B](B)
[9] -1 0 0x90000000 - 0x97ffffff (0x8000000) MX[B](B)
[10] -1 0 0xe0000000 - 0xe007ffff (0x80000) MX[B](B)
[11] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[12] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[13] -1 0 0x0000e300 - 0x0000e3ff (0x100) IX[B]
[14] -1 0 0x0000e200 - 0x0000e2ff (0x100) IX[B]
[15] -1 0 0x0000e100 - 0x0000e1ff (0x100) IX[B]
[16] -1 0 0x00001100 - 0x0000110f (0x10) IX[B]
[17] -1 0 0x00001300 - 0x0000131f (0x20) IX[B]
[18] -1 0 0x00001200 - 0x0000121f (0x20) IX[B]
(II) resource ranges after probing:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xf0000100 - 0xf00001ff (0x100) MX[B]
[6] -1 0 0xf0000000 - 0xf00000ff (0x100) MX[B]
[7] -1 0 0xa0000000 - 0x9fffffff (0x0) MX[B]O
[8] -1 0 0x98000000 - 0x9800ffff (0x10000) MX[B](B)
[9] -1 0 0x90000000 - 0x97ffffff (0x8000000) MX[B](B)
[10] -1 0 0xe0000000 - 0xe007ffff (0x80000) MX[B](B)
[11] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B]
[12] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
[13] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
[14] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[15] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[16] -1 0 0x0000e300 - 0x0000e3ff (0x100) IX[B]
[17] -1 0 0x0000e200 - 0x0000e2ff (0x100) IX[B]
[18] -1 0 0x0000e100 - 0x0000e1ff (0x100) IX[B]
[19] -1 0 0x00001100 - 0x0000110f (0x10) IX[B]
[20] -1 0 0x00001300 - 0x0000131f (0x20) IX[B]
[21] -1 0 0x00001200 - 0x0000121f (0x20) IX[B]
[22] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B]
[23] 0 0 0x000003c0 - 0x000003df (0x20) IS[B]
(II) Setting vga for screen 0.
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/X11R6/lib/modules/libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 0.1.0
ABI class: X.Org Video Driver, version 0.8
(**) SAVAGE(0): Depth 24, (--) framebuffer bpp 32
(==) SAVAGE(0): RGB weight 888
(==) SAVAGE(0): Default visual is TrueColor
(II) SAVAGE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(==) SAVAGE(0): Using HW cursor
(==) SAVAGE(0): Using video BIOS to set modes
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Loading /usr/X11R6/lib/modules/libvbe.so
(II) Module vbe: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.1.0
ABI class: X.Org Video Driver, version 0.8
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/X11R6/lib/modules/linux/libint10.so
(II) Module int10: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.0
ABI class: X.Org Video Driver, version 0.8
(II) SAVAGE(0): initializing int10
(II) SAVAGE(0): Primary V_BIOS segment is: 0xc000
(II) SAVAGE(0): VESA BIOS detected
(II) SAVAGE(0): VESA VBE Version 3.0
(II) SAVAGE(0): VESA VBE Total Mem: 31680 kB
(II) SAVAGE(0): VESA VBE OEM: S3 Graphics ProSavage DDR Family BIOS
(II) SAVAGE(0): VESA VBE OEM Software Rev: 2.0
(II) SAVAGE(0): VESA VBE OEM Vendor: S3 Garphics Incorporated.
(II) SAVAGE(0): VESA VBE OEM Product: VBE 3.0
(II) SAVAGE(0): VESA VBE OEM Product Rev: Rev 0.0
(--) SAVAGE(0): Chip: id 8d04, "ProSavage DDR-K"
(--) SAVAGE(0): Engine: "ProSavageDDR"
(--) SAVAGE(0): AGP card detected
(==) SAVAGE(0): Using AGP DMA
(==) SAVAGE(0): Will try command and vertex DMA mode
(==) SAVAGE(0): Using AGP 1x mode
(==) SAVAGE(0): Using 16 MB AGP aperture
(II) SAVAGE(0): mapping MMIO @ 0xe0000000 with size 0x80000
(==) SAVAGE(0): Using gamma correction (1.0, 1.0, 1.0)
(--) SAVAGE(0): probed videoram: 32768k
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Loading /usr/X11R6/lib/modules/libddc.so
(II) Module ddc: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.0
ABI class: X.Org Video Driver, version 0.8
(--) SAVAGE(0): No DDC signal
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Loading /usr/X11R6/lib/modules/libi2c.so
(II) Module i2c: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.2.0
ABI class: X.Org Video Driver, version 0.8
(II) SAVAGE(0): I2C bus "I2C bus" initialized.
(II) SAVAGE(0): I2C device "I2C bus:ddc2" registered at address 0xA0.
(II) SAVAGE(0): I2C device "I2C bus:ddc2" removed.
(--) SAVAGE(0): Detected current MCLK value of 14.318 MHz
(--) SAVAGE(0): 1024x768 TFT LCD panel detected and active
(--) SAVAGE(0): - Limiting video mode to 1024x768
(--) SAVAGE(0): Found 13 modes at this depth:
[10f] 320 x 200, 70Hz
[134] 320 x 240, 72Hz
[144] 400 x 300, 72Hz
[154] 512 x 384, 70Hz
[11e] 640 x 400, 70Hz
[112] 640 x 480, 60Hz, 75Hz, 85Hz, 100Hz, 160Hz
[115] 800 x 600, 60Hz, 75Hz, 85Hz
[118] 1024 x 768, 60Hz, 70Hz, 75Hz, 85Hz, 100Hz, 130Hz
[17b] 1280 x 768, 60Hz
[16a] 1280 x 960, 60Hz, 85Hz
[11b] 1280 x 1024, 60Hz, 75Hz, 85Hz, 100Hz
[13e] 1400 x 1050, 60Hz, 75Hz
[124] 1600 x 1200, 60Hz
(II) SAVAGE(0): My Monitor: Using hsync range of 31.50-150.00 kHz
(II) SAVAGE(0): My Monitor: Using vrefresh range of 75.00-85.00 Hz
(II) SAVAGE(0): Clock range: 10.00 to 220.00 MHz
(--) SAVAGE(0): No suitable BIOS mode found for 640x350 85Hz.
(II) SAVAGE(0): Not using default mode "640x350" (no mode of this name)
(--) SAVAGE(0): No suitable BIOS mode found for 320x175 85Hz.
(II) SAVAGE(0): Not using default mode "320x175" (no mode of this name)
(--) SAVAGE(0): Chose mode 11e at 70Hz.
(--) SAVAGE(0): Chose mode 10f at 70Hz.
(--) SAVAGE(0): No suitable BIOS mode found for 720x400 85Hz.
(II) SAVAGE(0): Not using default mode "720x400" (no mode of this name)
(--) SAVAGE(0): No suitable BIOS mode found for 360x200 85Hz.
(II) SAVAGE(0): Not using default mode "360x200" (no mode of this name)
(--) SAVAGE(0): Chose mode 112 at 60Hz.
(II) SAVAGE(0): Not using default mode "640x480" (vrefresh out of range)
(--) SAVAGE(0): Chose mode 134 at 72Hz.
(II) SAVAGE(0): Not using default mode "320x240" (vrefresh out of range)
(--) SAVAGE(0): Chose mode 112 at 75Hz.
(II) SAVAGE(0): Not using default mode "640x480" (vrefresh out of range)
(--) SAVAGE(0): Chose mode 134 at 72Hz.
(II) SAVAGE(0): Not using default mode "320x240" (vrefresh out of range)
(--) SAVAGE(0): Chose mode 112 at 75Hz.
(--) SAVAGE(0): Chose mode 134 at 72Hz.
(--) SAVAGE(0): Chose mode 112 at 85Hz.
(--) SAVAGE(0): Chose mode 134 at 72Hz.
(--) SAVAGE(0): Chose mode 115 at 60Hz.
(II) SAVAGE(0): Not using default mode "800x600" (vrefresh out of range)
(--) SAVAGE(0): Chose mode 144 at 72Hz.
(II) SAVAGE(0): Not using default mode "400x300" (vrefresh out of range)
(--) SAVAGE(0): Chose mode 115 at 60Hz.
(II) SAVAGE(0): Not using default mode "800x600" (vrefresh out of range)
(--) SAVAGE(0): Chose mode 144 at 72Hz.
(II) SAVAGE(0): Not using default mode "400x300" (vrefresh out of range)
(--) SAVAGE(0): Chose mode 115 at 75Hz.
(II) SAVAGE(0): Not using default mode "800x600" (vrefresh out of range)
(--) SAVAGE(0): Chose mode 144 at 72Hz.
(II) SAVAGE(0): Not using default mode "400x300" (vrefresh out of range)
(--) SAVAGE(0): Chose mode 115 at 75Hz.
(--) SAVAGE(0): Chose mode 144 at 72Hz.
(--) SAVAGE(0): Chose mode 115 at 85Hz.
(--) SAVAGE(0): Chose mode 144 at 72Hz.
(--) SAVAGE(0): Chose mode 118 at 85Hz.
(II) SAVAGE(0): Not using default mode "1024x768" (vrefresh out of range)
(--) SAVAGE(0): Chose mode 154 at 70Hz.
(II) SAVAGE(0): Not using default mode "512x384" (vrefresh out of range)
(--) SAVAGE(0): Chose mode 118 at 60Hz.
(II) SAVAGE(0): Not using default mode "1024x768" (vrefresh out of range)
(--) SAVAGE(0): Chose mode 154 at 70Hz.
(II) SAVAGE(0): Not using default mode "512x384" (vrefresh out of range)
(--) SAVAGE(0): Chose mode 118 at 70Hz.
(II) SAVAGE(0): Not using default mode "1024x768" (vrefresh out of range)
(--) SAVAGE(0): Chose mode 154 at 70Hz.
(II) SAVAGE(0): Not using default mode "512x384" (vrefresh out of range)
(--) SAVAGE(0): Chose mode 118 at 75Hz.
(--) SAVAGE(0): Chose mode 154 at 70Hz.
(--) SAVAGE(0): Chose mode 118 at 85Hz.
(--) SAVAGE(0): Chose mode 154 at 70Hz.
(II) SAVAGE(0): Not using default mode "1152x864" (exceeds panel dimensions)
(--) SAVAGE(0): No suitable BIOS mode found for 576x432 75Hz.
(II) SAVAGE(0): Not using default mode "576x432" (no mode of this name)
(II) SAVAGE(0): Not using default mode "1280x960" (exceeds panel dimensions)
(--) SAVAGE(0): Chose mode 112 at 60Hz.
(II) SAVAGE(0): Not using default mode "640x480" (vrefresh out of range)
(II) SAVAGE(0): Not using default mode "1280x960" (exceeds panel dimensions)
(--) SAVAGE(0): Chose mode 112 at 85Hz.
(II) SAVAGE(0): Not using default mode "1280x1024" (exceeds panel dimensions)
(--) SAVAGE(0): No suitable BIOS mode found for 640x512 60Hz.
(II) SAVAGE(0): Not using default mode "640x512" (no mode of this name)
(II) SAVAGE(0): Not using default mode "1280x1024" (exceeds panel dimensions)
(--) SAVAGE(0): No suitable BIOS mode found for 640x512 75Hz.
(II) SAVAGE(0): Not using default mode "640x512" (no mode of this name)
(II) SAVAGE(0): Not using default mode "1280x1024" (exceeds panel dimensions)
(--) SAVAGE(0): No suitable BIOS mode found for 640x512 85Hz.
(II) SAVAGE(0): Not using default mode "640x512" (no mode of this name)
(II) SAVAGE(0): Not using default mode "1600x1200" (exceeds panel dimensions)
(--) SAVAGE(0): Chose mode 115 at 60Hz.
(II) SAVAGE(0): Not using default mode "800x600" (vrefresh out of range)
(II) SAVAGE(0): Not using default mode "1600x1200" (exceeds panel dimensions)
(--) SAVAGE(0): Chose mode 115 at 60Hz.
(II) SAVAGE(0): Not using default mode "800x600" (vrefresh out of range)
(II) SAVAGE(0): Not using default mode "1600x1200" (exceeds panel dimensions)
(--) SAVAGE(0): Chose mode 115 at 75Hz.
(II) SAVAGE(0): Not using default mode "800x600" (vrefresh out of range)
(II) SAVAGE(0): Not using default mode "1600x1200" (exceeds panel dimensions)
(--) SAVAGE(0): Chose mode 115 at 75Hz.
(II) SAVAGE(0): Not using default mode "1600x1200" (bad mode clock/interlace/doublescan)
(--) SAVAGE(0): Chose mode 115 at 85Hz.
(II) SAVAGE(0): Not using default mode "1792x1344" (exceeds panel dimensions)
(--) SAVAGE(0): No suitable BIOS mode found for 896x672 60Hz.
(II) SAVAGE(0): Not using default mode "896x672" (no mode of this name)
(II) SAVAGE(0): Not using default mode "1792x1344" (bad mode clock/interlace/doublescan)
(--) SAVAGE(0): No suitable BIOS mode found for 896x672 75Hz.
(II) SAVAGE(0): Not using default mode "896x672" (no mode of this name)
(II) SAVAGE(0): Not using default mode "1856x1392" (exceeds panel dimensions)
(--) SAVAGE(0): No suitable BIOS mode found for 928x696 60Hz.
(II) SAVAGE(0): Not using default mode "928x696" (no mode of this name)
(II) SAVAGE(0): Not using default mode "1856x1392" (bad mode clock/interlace/doublescan)
(--) SAVAGE(0): No suitable BIOS mode found for 928x696 75Hz.
(II) SAVAGE(0): Not using default mode "928x696" (no mode of this name)
(II) SAVAGE(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan)
(--) SAVAGE(0): No suitable BIOS mode found for 960x720 60Hz.
(II) SAVAGE(0): Not using default mode "960x720" (no mode of this name)
(II) SAVAGE(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan)
(--) SAVAGE(0): No suitable BIOS mode found for 960x720 75Hz.
(II) SAVAGE(0): Not using default mode "960x720" (no mode of this name)
(--) SAVAGE(0): No suitable BIOS mode found for 832x624 74Hz.
(II) SAVAGE(0): Not using default mode "832x624" (no mode of this name)
(--) SAVAGE(0): No suitable BIOS mode found for 416x312 74Hz.
(II) SAVAGE(0): Not using default mode "416x312" (no mode of this name)
(II) SAVAGE(0): Not using default mode "1152x768" (exceeds panel dimensions)
(--) SAVAGE(0): No suitable BIOS mode found for 576x384 54Hz.
(II) SAVAGE(0): Not using default mode "576x384" (no mode of this name)
(II) SAVAGE(0): Not using default mode "1400x1050" (exceeds panel dimensions)
(--) SAVAGE(0): No suitable BIOS mode found for 700x525 59Hz.
(II) SAVAGE(0): Not using default mode "700x525" (no mode of this name)
(II) SAVAGE(0): Not using default mode "1400x1050" (exceeds panel dimensions)
(--) SAVAGE(0): No suitable BIOS mode found for 700x525 74Hz.
(II) SAVAGE(0): Not using default mode "700x525" (no mode of this name)
(II) SAVAGE(0): Not using default mode "1600x1024" (exceeds panel dimensions)
(--) SAVAGE(0): No suitable BIOS mode found for 800x512 60Hz.
(II) SAVAGE(0): Not using default mode "800x512" (no mode of this name)
(II) SAVAGE(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan)
(--) SAVAGE(0): No suitable BIOS mode found for 960x720 85Hz.
(II) SAVAGE(0): Not using default mode "960x720" (no mode of this name)
(II) SAVAGE(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
(--) SAVAGE(0): Chose mode 118 at 60Hz.
(II) SAVAGE(0): Not using default mode "1024x768" (vrefresh out of range)
(II) SAVAGE(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
(--) SAVAGE(0): Chose mode 118 at 75Hz.
(II) SAVAGE(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
(--) SAVAGE(0): Chose mode 118 at 85Hz.
(--) SAVAGE(0): Chose mode 118 at 85Hz.
(--) SAVAGE(0): Chose mode 115 at 85Hz.
(--) SAVAGE(0): Chose mode 112 at 85Hz.
(--) SAVAGE(0): Chose mode 118 at 85Hz.
(--) SAVAGE(0): Chose mode 118 at 75Hz.
(--) SAVAGE(0): Chose mode 118 at 75Hz.
(--) SAVAGE(0): Chose mode 115 at 85Hz.
(--) SAVAGE(0): Chose mode 115 at 75Hz.
(--) SAVAGE(0): Chose mode 115 at 75Hz.
(--) SAVAGE(0): Chose mode 112 at 85Hz.
(--) SAVAGE(0): Chose mode 112 at 75Hz.
(--) SAVAGE(0): Chose mode 11e at 70Hz.
(--) SAVAGE(0): Chose mode 154 at 70Hz.
(--) SAVAGE(0): Chose mode 154 at 70Hz.
(--) SAVAGE(0): Chose mode 144 at 72Hz.
(--) SAVAGE(0): Chose mode 144 at 72Hz.
(--) SAVAGE(0): Chose mode 134 at 72Hz.
(--) SAVAGE(0): Chose mode 134 at 72Hz.
(--) SAVAGE(0): Chose mode 10f at 70Hz.
(--) SAVAGE(0): Virtual size is 1024x768 (pitch 1024)
(**) SAVAGE(0): *Default mode "1024x768": 194.0 MHz, 137.0 kHz, 85.0 Hz (D)
(II) SAVAGE(0): Modeline "1024x768" 194.02 1024 1108 1220 1416 768 768 770 806 doublescan -hsync +vsync
(**) SAVAGE(0): *Default mode "800x600": 56.3 MHz, 53.7 kHz, 85.1 Hz
(II) SAVAGE(0): Modeline "800x600" 56.30 800 832 896 1048 600 601 604 631 +hsync +vsync
(**) SAVAGE(0): *Default mode "640x480": 74.2 MHz, 85.9 kHz, 85.1 Hz (D)
(II) SAVAGE(0): Modeline "640x480" 74.25 640 672 752 864 480 480 482 505 doublescan +hsync +vsync
(**) SAVAGE(0): Default mode "1024x768": 94.5 MHz, 68.7 kHz, 85.0 Hz
(II) SAVAGE(0): Modeline "1024x768" 94.50 1024 1072 1168 1376 768 769 772 808 +hsync +vsync
(**) SAVAGE(0): Default mode "1024x768": 78.8 MHz, 60.1 kHz, 75.1 Hz
(II) SAVAGE(0): Modeline "1024x768" 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync
(**) SAVAGE(0): Default mode "1024x768": 170.2 MHz, 120.2 kHz, 75.0 Hz (D)
(II) SAVAGE(0): Modeline "1024x768" 170.24 1024 1108 1220 1416 768 768 770 801 doublescan -hsync +vsync
(**) SAVAGE(0): Default mode "800x600": 114.8 MHz, 106.2 kHz, 85.0 Hz (D)
(II) SAVAGE(0): Modeline "800x600" 114.75 800 832 928 1080 600 600 602 625 doublescan +hsync +vsync
(**) SAVAGE(0): Default mode "800x600": 49.5 MHz, 46.9 kHz, 75.0 Hz
(II) SAVAGE(0): Modeline "800x600" 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync
(**) SAVAGE(0): Default mode "800x600": 101.2 MHz, 93.8 kHz, 75.0 Hz (D)
(II) SAVAGE(0): Modeline "800x600" 101.25 800 832 928 1080 600 600 602 625 doublescan +hsync +vsync
(**) SAVAGE(0): Default mode "640x480": 36.0 MHz, 43.3 kHz, 85.0 Hz
(II) SAVAGE(0): Modeline "640x480" 36.00 640 696 752 832 480 481 484 509 -hsync -vsync
(**) SAVAGE(0): Default mode "640x480": 31.5 MHz, 37.5 kHz, 75.0 Hz
(II) SAVAGE(0): Modeline "640x480" 31.50 640 656 720 840 480 481 484 500 -hsync -vsync
(**) SAVAGE(0): Default mode "640x400": 31.5 MHz, 37.9 kHz, 85.1 Hz
(II) SAVAGE(0): Modeline "640x400" 31.50 640 672 736 832 400 401 404 445 -hsync +vsync
(**) SAVAGE(0): Default mode "512x384": 47.2 MHz, 68.7 kHz, 85.0 Hz (D)
(II) SAVAGE(0): Modeline "512x384" 47.25 512 536 584 688 384 384 386 404 doublescan +hsync +vsync
(**) SAVAGE(0): Default mode "512x384": 39.4 MHz, 60.1 kHz, 75.1 Hz (D)
(II) SAVAGE(0): Modeline "512x384" 39.40 512 520 568 656 384 384 386 400 doublescan +hsync +vsync
(**) SAVAGE(0): Default mode "400x300": 28.1 MHz, 53.7 kHz, 85.3 Hz (D)
(II) SAVAGE(0): Modeline "400x300" 28.15 400 416 448 524 300 300 302 315 doublescan +hsync +vsync
(**) SAVAGE(0): Default mode "400x300": 24.8 MHz, 46.9 kHz, 75.1 Hz (D)
(II) SAVAGE(0): Modeline "400x300" 24.75 400 408 448 528 300 300 302 312 doublescan +hsync +vsync
(**) SAVAGE(0): Default mode "320x240": 18.0 MHz, 43.3 kHz, 85.2 Hz (D)
(II) SAVAGE(0): Modeline "320x240" 18.00 320 348 376 416 240 240 242 254 doublescan -hsync -vsync
(**) SAVAGE(0): Default mode "320x240": 15.8 MHz, 37.5 kHz, 75.0 Hz (D)
(II) SAVAGE(0): Modeline "320x240" 15.75 320 328 360 420 240 240 242 250 doublescan -hsync -vsync
(**) SAVAGE(0): Default mode "320x200": 15.8 MHz, 37.9 kHz, 85.3 Hz (D)
(II) SAVAGE(0): Modeline "320x200" 15.75 320 336 368 416 200 200 202 222 doublescan -hsync +vsync
(==) SAVAGE(0): DPI set to (75, 75)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/X11R6/lib/modules/libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.2
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/X11R6/lib/modules/libxaa.so
(II) Module xaa: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.2.0
ABI class: X.Org Video Driver, version 0.8
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Loading /usr/X11R6/lib/modules/libramdac.so
(II) Module ramdac: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 0.1.0
ABI class: X.Org Video Driver, version 0.8
(--) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] 0 0 0x90000000 - 0x97ffffff (0x8000000) MS[B]
[1] 0 0 0xe0000000 - 0xe007ffff (0x80000) MS[B]
[2] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[3] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[4] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[5] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[6] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[7] -1 0 0xf0000100 - 0xf00001ff (0x100) MX[B]
[8] -1 0 0xf0000000 - 0xf00000ff (0x100) MX[B]
[9] -1 0 0xa0000000 - 0x9fffffff (0x0) MX[B]O
[10] -1 0 0x98000000 - 0x9800ffff (0x10000) MX[B](B)
[11] -1 0 0x90000000 - 0x97ffffff (0x8000000) MX[B](B)
[12] -1 0 0xe0000000 - 0xe007ffff (0x80000) MX[B](B)
[13] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B](OprD)
[14] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B](OprD)
[15] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B](OprD)
[16] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[17] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[18] -1 0 0x0000e300 - 0x0000e3ff (0x100) IX[B]
[19] -1 0 0x0000e200 - 0x0000e2ff (0x100) IX[B]
[20] -1 0 0x0000e100 - 0x0000e1ff (0x100) IX[B]
[21] -1 0 0x00001100 - 0x0000110f (0x10) IX[B]
[22] -1 0 0x00001300 - 0x0000131f (0x20) IX[B]
[23] -1 0 0x00001200 - 0x0000121f (0x20) IX[B]
[24] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B](OprU)
[25] 0 0 0x000003c0 - 0x000003df (0x20) IS[B](OprU)
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Reloading /usr/X11R6/lib/modules/linux/libint10.so
(II) SAVAGE(0): initializing int10
(II) SAVAGE(0): Primary V_BIOS segment is: 0xc000
(II) SAVAGE(0): VESA BIOS detected
(II) SAVAGE(0): VESA VBE Version 3.0
(II) SAVAGE(0): VESA VBE Total Mem: 31680 kB
(II) SAVAGE(0): VESA VBE OEM: S3 Graphics ProSavage DDR Family BIOS
(II) SAVAGE(0): VESA VBE OEM Software Rev: 2.0
(II) SAVAGE(0): VESA VBE OEM Vendor: S3 Garphics Incorporated.
(II) SAVAGE(0): VESA VBE OEM Product: VBE 3.0
(II) SAVAGE(0): VESA VBE OEM Product Rev: Rev 0.0
(--) SAVAGE(0): mapping framebuffer @ 0x90000000 with size 0x2000000
(==) SAVAGE(0): Write-combining range (0x90000000,0x2000000)
(II) SAVAGE(0): Splitting WC range: base: 0x92000000, size: 0x5000000
(II) SAVAGE(0): Splitting WC range: base: 0x94000000, size: 0x3000000
(==) SAVAGE(0): Write-combining range (0x96000000,0x1000000)
(==) SAVAGE(0): Write-combining range (0x94000000,0x3000000)
(==) SAVAGE(0): Write-combining range (0x92000000,0x5000000)
(II) SAVAGE(0): map aperture:0xb0887000
(II) SAVAGE(0): 9348 kB of Videoram needed for 3D; 32768 kB of Videoram available
(II) SAVAGE(0): Sufficient Videoram available for 3D
(II) SAVAGE(0): [drm] bpp: 32 depth: 24
(II) SAVAGE(0): [drm] Sarea 2200+284: 2484
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 9, (OK)
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 9, (OK)
drmOpenByBusid: Searching for BusID pci:0000:01:00.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 9, (OK)
drmOpenByBusid: drmOpenMinor returns 9
drmOpenByBusid: drmGetBusid reports pci:0000:01:00.0
(II) SAVAGE(0): [drm] DRM interface version 1.2
(II) SAVAGE(0): [drm] created "savage" driver at busid "pci:0000:01:00.0"
(II) SAVAGE(0): [drm] added 8192 byte SAREA at 0xcf157000
(II) SAVAGE(0): [drm] mapped SAREA 0xcf157000 to 0xb0875000
(II) SAVAGE(0): [drm] framebuffer handle = 0x90000000
(II) SAVAGE(0): [drm] added 1 reserved context for kernel
(II) SAVAGE(0): [agp] Mode 0x1f000201 [AGP 0x1106/0x3156; Card 0x5333/0x8d04]
(II) SAVAGE(0): [agp] 16384 kB allocated with handle 0x00000001
(II) SAVAGE(0): [agp] command DMA handle = 0xa0000000
(II) SAVAGE(0): [agp] agpTextures handle = 0xa0100000
(II) SAVAGE(0): [drm] aperture handle = 0x92000000
(II) SAVAGE(0): [drm] Enabling ShadowStatus for DRI.
(II) SAVAGE(0): [drm] Status handle = 0x05aa2000
(II) SAVAGE(0): [drm] Status page mapped at 0xb0874000
(II) SAVAGE(0): [dri] visual configs initialized
(**) SAVAGE(0): DRI is enabled
(--) SAVAGE(0): Chose mode 118 at 85Hz.
(II) SAVAGE(0): virtualX:1024,virtualY:768
(II) SAVAGE(0): bpp:32,tiledwidthBytes:4096,tiledBufferSize:3145728
(II) SAVAGE(0): bpp:32,widthBytes:4096,BufferSize:3145728
(II) SAVAGE(0): videoRambytes:0x02000000
(II) SAVAGE(0): textureSize:0x014df000
(II) SAVAGE(0): textureSize:0x014df000
(II) SAVAGE(0): textureOffset:0x00b00000
(II) SAVAGE(0): depthOffset:0x00800000,depthPitch:4096
(II) SAVAGE(0): backOffset:0x00500000,backPitch:4096
(II) SAVAGE(0): Memory manager initialized to (0,0) (1024,1279)
(II) SAVAGE(0): Largest offscreen area available: 1024 x 511
(II) SAVAGE(0): Reserved back buffer at offset 0x500000
(II) SAVAGE(0): Reserved depth buffer at offset 0x800000
(II) SAVAGE(0): Reserved 21372 kb for textures at offset 0xb00000
(II) SAVAGE(0): Using XFree86 Acceleration Architecture (XAA)
Screen to screen bit blits
Solid filled rectangles
8x8 mono pattern filled rectangles
Indirect CPU to Screen color expansion
Solid Lines
Image Writes
Offscreen Pixmaps
Setting up tile and stipple cache:
24 128x128 slots
(==) SAVAGE(0): Backing store disabled
(II) SAVAGE(0): X context handle = 0x1
(II) SAVAGE(0): [DRI] installation complete
(II) SAVAGE(0): [junkers]pSAVAGEDRIServer:
(II) SAVAGE(0): [junkers] reserved_map_agpstart:0x00000000
(II) SAVAGE(0): [junkers] reserved_map_idx:0x00000000
(II) SAVAGE(0): [junkers] sarea_priv_offset:0x00000000
(II) SAVAGE(0): [junkers] chipset:0x00000000
(II) SAVAGE(0): [junkers] sgram:0x00000000
(II) SAVAGE(0): [junkers] frontbufferSize:0x00300000
(II) SAVAGE(0): [junkers] frontOffset:0x00000000
(II) SAVAGE(0): [junkers] frontPitch:0x00001000
(II) SAVAGE(0): [junkers] backbufferSize:0x00300000
(II) SAVAGE(0): [junkers] backOffset:0x00500000
(II) SAVAGE(0): [junkers] backPitch:0x00001000
(II) SAVAGE(0): [junkers] depthbufferSize:0x00300000
(II) SAVAGE(0): [junkers] depthOffset:0x00800000
(II) SAVAGE(0): [junkers] depthPitch:0x00001000
(II) SAVAGE(0): [junkers] textureOffset:0x00b00000
(II) SAVAGE(0): [junkers] textureSize:0x014df000
(II) SAVAGE(0): [junkers] textureSize:0x014df000
(II) SAVAGE(0): [junkers] logTextureGranularity:0x00000000
(II) SAVAGE(0): [junkers] agp:handle:0x00000001
(II) SAVAGE(0): [junkers] agp:offset:0x01000000
(II) SAVAGE(0): [junkers] agp:size:0x01000000
(II) SAVAGE(0): [junkers] agp0x00000000
(II) SAVAGE(0): [junkers] registers:handle:0xe0000000
(II) SAVAGE(0): [junkers] registers:offset:0x00000000
(II) SAVAGE(0): [junkers] registers:size:0x00080000
(II) SAVAGE(0): [junkers] registers0x00000000
(II) SAVAGE(0): [junkers] status:handle:0x05aa2000
(II) SAVAGE(0): [junkers] status:offset:0x00000000
(II) SAVAGE(0): [junkers] status:size:0x00001000
(II) SAVAGE(0): [junkers] status0xb0874000
(II) SAVAGE(0): [junkers] agpTextures:handle:0xa0100000
(II) SAVAGE(0): [junkers] agpTextures:offset:0x00100000
(II) SAVAGE(0): [junkers] agpTextures:size:0x00f00000
(II) SAVAGE(0): [junkers] apgTextures0x00000000
(II) SAVAGE(0): [junkers] logAgpTextureGranularity:0x00000000
(II) SAVAGE(0): [junkers] cmdDma:handle:0xa0000000
(II) SAVAGE(0): [junkers] cmdDma:offset:0x00000000
(II) SAVAGE(0): [junkers] cmdDma:size:0x00100000
(II) SAVAGE(0): [junkers] cmdDma0x00000000
(II) SAVAGE(0): [junkers]pSAVAGEDRI:
(II) SAVAGE(0): [junkers] chipset:0x00000006
(II) SAVAGE(0): [junkers] width:0x00000400
(II) SAVAGE(0): [junkers] height:0x00000300
(II) SAVAGE(0): [junkers] mem:0x02000000
(II) SAVAGE(0): [junkers] cpp:4
(II) SAVAGE(0): [junkers] zpp:4
(II) SAVAGE(0): [junkers] agpMode:1
(II) SAVAGE(0): [junkers] bufferSize:65536
(II) SAVAGE(0): [junkers] frontbufferSize:0x00300000
(II) SAVAGE(0): [junkers] frontOffset:0x00000000
(II) SAVAGE(0): [junkers] backbufferSize:0x00300000
(II) SAVAGE(0): [junkers] backOffset:0x00500000
(II) SAVAGE(0): [junkers] depthbufferSize:0x00300000
(II) SAVAGE(0): [junkers] depthOffset:0x00800000
(II) SAVAGE(0): [junkers] textureOffset:0x00b00000
(II) SAVAGE(0): [junkers] textureSize:0x01400000
(II) SAVAGE(0): [junkers] logTextureGranularity:0x00000015
(II) SAVAGE(0): [junkers] agpTextureHandle:0xa0100000
(II) SAVAGE(0): [junkers] agpTextureSize:0x00f00000
(II) SAVAGE(0): [junkers] logAgpTextureGranularity:0x00000014
(II) SAVAGE(0): [junkers] apertureHandle:0x92000000
(II) SAVAGE(0): [junkers] apertureSize:0x05000000
(II) SAVAGE(0): [junkers] aperturePitch:0x00002000
(II) SAVAGE(0): [junkers] statusHandle:0x05aa2000
(II) SAVAGE(0): [junkers] statusSize:0x00001000
(II) SAVAGE(0): [junkers] sarea_priv_offset:0x00000898
(II) SAVAGE(0): Direct rendering enabled
(==) RandR enabled
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension LBX
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension XFree86-Bigfont
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing built-in extension XEVIE
(**) Option "Protocol" "IMPS/2"
(**) Mouse1: Device: "/dev/mouse"
(**) Mouse1: Protocol: "IMPS/2"
(**) Option "CorePointer"
(**) Mouse1: Core Pointer
(**) Option "Device" "/dev/mouse"
(**) Option "Buttons" "3"
(==) Mouse1: Emulate3Buttons, Emulate3Timeout: 50
(**) Option "ZAxisMapping" "4 5"
(**) Mouse1: ZAxisMapping: buttons 4 and 5
(**) Mouse1: Buttons: 9
(**) Option "CoreKeyboard"
(**) Keyboard1: Core Keyboard
(**) Option "Protocol" "standard"
(**) Keyboard1: Protocol: standard
(**) Option "AutoRepeat" "500 30"
(**) Option "XkbRules" "xorg"
(**) Keyboard1: XkbRules: "xorg"
(**) Option "XkbModel" "pc105"
(**) Keyboard1: XkbModel: "pc105"
(**) Option "XkbLayout" "us"
(**) Keyboard1: XkbLayout: "us"
(**) Option "CustomKeycodes" "off"
(**) Keyboard1: CustomKeycodes disabled
(II) XINPUT: Adding extended input device "Keyboard1" (type: KEYBOARD)
(II) XINPUT: Adding extended input device "Mouse1" (type: MOUSE)
(II) Mouse1: ps2EnableDataReporting: succeeded
Could not init font path element /usr/X11R6/lib/X11/fonts/local/, removing from list!
Could not init font path element /usr/X11R6/lib/X11/fonts/75dpi/:unscaled, removing from list!
Could not init font path element /usr/X11R6/lib/X11/fonts/100dpi/:unscaled, removing from list!
Could not init font path element /usr/X11R6/lib/X11/fonts/Type1/, removing from list!
Could not init font path element /usr/X11R6/lib/X11/fonts/CID/, removing from list!
Could not init font path element /usr/X11R6/lib/X11/fonts/Speedo/, removing from list!
Could not init font path element /usr/X11R6/lib/X11/fonts/75dpi/, removing from list!
Could not init font path element /usr/X11R6/lib/X11/fonts/100dpi/, removing from list!

Messaggio da **phobos3576** » mar 18 lug 2006, 3:47

In effetti sembra tutto a posto.

Ho notato però le seguenti linee:

Codice: Seleziona tutto

(II) SAVAGE(0): My Monitor: Using hsync range of 31.50-150.00 kHz
(II) SAVAGE(0): My Monitor: Using vrefresh range of 75.00-85.00 Hz

Ma non è che hai rimesso il vecchio xorg.conf ?
Ti avevo suggerito di modificare quei valori nella sezione "Monitor", anche se non c'entrano nulla con l'accelerazione hardware.

Comunque questa situazione mi sembra veramente strana; i recenti kernel hanno il pieno supporto per l'accelerazione grafica delle savage e lo stesso dicasi per Xorg 6.9 o superiore.
Come risulta anche dalla documentazione presente nel sito ufficiale del progetto DRI, con le versioni aggiornate del kernel e di Xorg non c'é bisogno di nessuna procedura particolare per abilitare l'accelerazione grafica delle savage.

Non so proprio cosa pensare.

Prima di eseguire startx, dai il comando lsmod | less e controlla che siano stati già caricati i moduli agpgart e via_agp; poi esegui il comando modprobe savage e a questo punto lancia startx.

Questi esperimenti li devi fare inizialmente da utente root.

Controlla che in /etc/rc.d/rc.moules non ci siano delle linee che caricano moduli AGP (eventualmente, commentale); questo lavoro, infatti, viene eseguito in automatico dal kernel.

Nelle precedenti risposte ho dato per scontato che il tuo AGP Bridge sia basato sul chipset VIA; per esserne certi, prova a postare l'output del comando /sbin/lspci.

Ultime notizie: nei recentissimi kernel 2.6.17.3 e superiori, sono presenti anche queste nuove opzioni relative al supporto del framebuffer per le savage:

Codice: Seleziona tutto

FB_SAVAGE=m
FB_SAVAGE_I2C=m
FB_SAVAGE_ACCEL=m

Non so se possano risolvere il tuo problema.
Se attivi queste opzioni, prima di lanciare startx devi eseguire i comandi:

modprobe savage
modprobe savagefb

Puoi automatizzare questa procedura mettendo i precedenti comandi nel file /etc/rc.d/rc.local.

P.S. Quando ricompili un nuovo kernel, ricordati di riciclare il vecchio file .config; quindi, dopo aver dato il comando

make mrproper

copia il vecchio .config in /usr/src/linux (dove linux è un link simbolico che punta alla directory dove hai decompresso il nuovo kernel).

n3tfr33 · Messaggio da **n3tfr33** » mar 18 lug 2006, 4:33

allora:
1) Il primo esperimento di ricompilazione del kernel è stato disastroso e ho dovuto reinstallare tutto perciò mi ero dimenticato di risistemare il monitor...adesso fatto
2) Ho controllato con lsmod | less e tutti i moduli sono caricati
3) c'è un problemino...quando lancio /etc/rc.d/rc.moules mi esce questo errore: Module dependencies up to date (no new kernel modules found). Use 'slax noagp' boot parameter to skip the following step:...non ho capito che vuol dire!!!
4) ti posto un po' di file per vedere se trovi il problema:
.config
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.17.4
# Mon Jul 17 04:05:04 2006
#
CONFIG_X86_32=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_DMI=y

#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_INIT_ENV_ARG_LIMIT=32

#
# General setup
#
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
CONFIG_SYSCTL=y
# CONFIG_AUDIT is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
# CONFIG_RELAY is not set
CONFIG_INITRAMFS_SOURCE=""
CONFIG_UID16=y
CONFIG_VM86=y
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
# CONFIG_EMBEDDED is not set
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SHMEM=y
CONFIG_SLAB=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
# CONFIG_SLOB is not set

#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_KMOD=y

#
# Block layer
#
CONFIG_LBD=y
# CONFIG_BLK_DEV_IO_TRACE is not set
CONFIG_LSF=y

#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
CONFIG_DEFAULT_AS=y
# CONFIG_DEFAULT_DEADLINE is not set
# CONFIG_DEFAULT_CFQ is not set
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="anticipatory"

#
# Processor type and features
#
# CONFIG_SMP is not set
CONFIG_X86_PC=y
# CONFIG_X86_ELAN is not set
# CONFIG_X86_VOYAGER is not set
# CONFIG_X86_NUMAQ is not set
# CONFIG_X86_SUMMIT is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_VISWS is not set
# CONFIG_X86_GENERICARCH is not set
# CONFIG_X86_ES7000 is not set
# CONFIG_M386 is not set
CONFIG_M486=y
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUMM is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MK8 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MEFFICEON is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MGEODEGX1 is not set
# CONFIG_MGEODE_LX is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
CONFIG_X86_GENERIC=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_L1_CACHE_SHIFT=7
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_X86_PPRO_FENCE=y
CONFIG_X86_F00F_BUG=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_ALIGNMENT_16=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_HPET_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
CONFIG_PREEMPT_NONE=y
# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT is not set
# CONFIG_X86_UP_APIC is not set
CONFIG_X86_MCE=y
# CONFIG_X86_MCE_NONFATAL is not set
CONFIG_TOSHIBA=m
CONFIG_I8K=m
CONFIG_X86_REBOOTFIXUPS=y
CONFIG_MICROCODE=m
CONFIG_X86_MSR=m
CONFIG_X86_CPUID=m

#
# Firmware Drivers
#
CONFIG_EDD=m
CONFIG_DELL_RBU=m
CONFIG_DCDBAS=m
CONFIG_NOHIGHMEM=y
# CONFIG_HIGHMEM4G is not set
# CONFIG_HIGHMEM64G is not set
CONFIG_PAGE_OFFSET=0xC0000000
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_SPARSEMEM_STATIC=y
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_MATH_EMULATION=y
CONFIG_MTRR=y
# CONFIG_EFI is not set
# CONFIG_REGPARM is not set
CONFIG_SECCOMP=y
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
# CONFIG_KEXEC is not set
CONFIG_PHYSICAL_START=0x100000

#
# Power management options (ACPI, APM)
#
CONFIG_PM=y
CONFIG_PM_LEGACY=y
# CONFIG_PM_DEBUG is not set
# CONFIG_SOFTWARE_SUSPEND is not set

#
# ACPI (Advanced Configuration and Power Interface) Support
#
CONFIG_ACPI=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_SLEEP_PROC_FS=y
# CONFIG_ACPI_SLEEP_PROC_SLEEP is not set
CONFIG_ACPI_AC=m
CONFIG_ACPI_BATTERY=m
CONFIG_ACPI_BUTTON=m
CONFIG_ACPI_VIDEO=m
# CONFIG_ACPI_HOTKEY is not set
CONFIG_ACPI_FAN=m
CONFIG_ACPI_PROCESSOR=m
CONFIG_ACPI_THERMAL=m
CONFIG_ACPI_ASUS=m
CONFIG_ACPI_IBM=m
# CONFIG_ACPI_IBM_DOCK is not set
CONFIG_ACPI_TOSHIBA=m
CONFIG_ACPI_BLACKLIST_YEAR=0
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_SYSTEM=y
CONFIG_X86_PM_TIMER=y
CONFIG_ACPI_CONTAINER=m

#
# APM (Advanced Power Management) BIOS Support
#
CONFIG_APM=y
# CONFIG_APM_IGNORE_USER_SUSPEND is not set
# CONFIG_APM_DO_ENABLE is not set
# CONFIG_APM_CPU_IDLE is not set
# CONFIG_APM_DISPLAY_BLANK is not set
# CONFIG_APM_RTC_IS_GMT is not set
# CONFIG_APM_ALLOW_INTS is not set
# CONFIG_APM_REAL_MODE_POWER_OFF is not set

#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=m
# CONFIG_CPU_FREQ_DEBUG is not set
CONFIG_CPU_FREQ_STAT=m
CONFIG_CPU_FREQ_STAT_DETAILS=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set
CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE=y
CONFIG_CPU_FREQ_GOV_PERFORMANCE=m
CONFIG_CPU_FREQ_GOV_POWERSAVE=m
CONFIG_CPU_FREQ_GOV_USERSPACE=y
CONFIG_CPU_FREQ_GOV_ONDEMAND=m
CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m

#
# CPUFreq processor drivers
#
CONFIG_X86_ACPI_CPUFREQ=m
CONFIG_X86_POWERNOW_K6=m
CONFIG_X86_POWERNOW_K7=m
CONFIG_X86_POWERNOW_K7_ACPI=y
CONFIG_X86_POWERNOW_K8=m
CONFIG_X86_POWERNOW_K8_ACPI=y
CONFIG_X86_GX_SUSPMOD=m
CONFIG_X86_SPEEDSTEP_CENTRINO=m
CONFIG_X86_SPEEDSTEP_CENTRINO_ACPI=y
CONFIG_X86_SPEEDSTEP_CENTRINO_TABLE=y
CONFIG_X86_SPEEDSTEP_ICH=m
CONFIG_X86_SPEEDSTEP_SMI=m
CONFIG_X86_P4_CLOCKMOD=m
CONFIG_X86_CPUFREQ_NFORCE2=m
CONFIG_X86_LONGRUN=m

#
# shared options
#
# CONFIG_X86_ACPI_CPUFREQ_PROC_INTF is not set
CONFIG_X86_SPEEDSTEP_LIB=m
# CONFIG_X86_SPEEDSTEP_RELAXED_CAP_CHECK is not set

#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GOMMCONFIG is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
CONFIG_PCIEPORTBUS=y
CONFIG_HOTPLUG_PCI_PCIE=m
# CONFIG_HOTPLUG_PCI_PCIE_POLL_EVENT_MODE is not set
CONFIG_ISA_DMA_API=y
CONFIG_ISA=y
# CONFIG_EISA is not set
# CONFIG_MCA is not set
CONFIG_SCx200=m

#
# PCCARD (PCMCIA/CardBus) support
#
CONFIG_PCCARD=m
# CONFIG_PCMCIA_DEBUG is not set
CONFIG_PCMCIA=m
CONFIG_PCMCIA_LOAD_CIS=y
CONFIG_PCMCIA_IOCTL=y
CONFIG_CARDBUS=y

#
# PC-card bridges
#
CONFIG_YENTA=m
CONFIG_YENTA_O2=y
CONFIG_YENTA_RICOH=y
CONFIG_YENTA_TI=y
CONFIG_YENTA_ENE_TUNE=y
CONFIG_YENTA_TOSHIBA=y
CONFIG_PD6729=m
CONFIG_I82092=m
CONFIG_I82365=m
CONFIG_TCIC=m
CONFIG_PCMCIA_PROBE=y
CONFIG_PCCARD_NONSTATIC=m

#
# PCI Hotplug Support
#
CONFIG_HOTPLUG_PCI=y
CONFIG_HOTPLUG_PCI_FAKE=m
CONFIG_HOTPLUG_PCI_COMPAQ=m
# CONFIG_HOTPLUG_PCI_COMPAQ_NVRAM is not set
CONFIG_HOTPLUG_PCI_ACPI=m
CONFIG_HOTPLUG_PCI_ACPI_IBM=m
# CONFIG_HOTPLUG_PCI_CPCI is not set
CONFIG_HOTPLUG_PCI_SHPC=m
# CONFIG_HOTPLUG_PCI_SHPC_POLL_EVENT_MODE is not set

#
# Executable file formats
#
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_MISC=m

#
# Networking
#
CONFIG_NET=y

#
# Networking options
#
# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=y
CONFIG_XFRM=y
CONFIG_XFRM_USER=y
CONFIG_NET_KEY=m
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_ADVANCED_ROUTER=y
CONFIG_ASK_IP_FIB_HASH=y
# CONFIG_IP_FIB_TRIE is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_MULTIPLE_TABLES=y
CONFIG_IP_ROUTE_FWMARK=y
CONFIG_IP_ROUTE_MULTIPATH=y
# CONFIG_IP_ROUTE_MULTIPATH_CACHED is not set
CONFIG_IP_ROUTE_VERBOSE=y
# CONFIG_IP_PNP is not set
CONFIG_NET_IPIP=m
CONFIG_NET_IPGRE=m
CONFIG_NET_IPGRE_BROADCAST=y
CONFIG_IP_MROUTE=y
CONFIG_IP_PIMSM_V1=y
CONFIG_IP_PIMSM_V2=y
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_TUNNEL=m
CONFIG_INET_TUNNEL=m
CONFIG_INET_DIAG=m
CONFIG_INET_TCP_DIAG=m
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_BIC=y

#
# IP: Virtual Server Configuration
#
CONFIG_IP_VS=m
# CONFIG_IP_VS_DEBUG is not set
CONFIG_IP_VS_TAB_BITS=12

#
# IPVS transport protocol load balancing support
#
CONFIG_IP_VS_PROTO_TCP=y
CONFIG_IP_VS_PROTO_UDP=y
CONFIG_IP_VS_PROTO_ESP=y
CONFIG_IP_VS_PROTO_AH=y

#
# IPVS scheduler
#
CONFIG_IP_VS_RR=m
CONFIG_IP_VS_WRR=m
CONFIG_IP_VS_LC=m
CONFIG_IP_VS_WLC=m
CONFIG_IP_VS_LBLC=m
CONFIG_IP_VS_LBLCR=m
CONFIG_IP_VS_DH=m
CONFIG_IP_VS_SH=m
CONFIG_IP_VS_SED=m
CONFIG_IP_VS_NQ=m

#
# IPVS application helper
#
CONFIG_IP_VS_FTP=m
CONFIG_IPV6=m
CONFIG_IPV6_PRIVACY=y
# CONFIG_IPV6_ROUTER_PREF is not set
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
CONFIG_INET6_XFRM_TUNNEL=m
CONFIG_INET6_TUNNEL=m
CONFIG_IPV6_TUNNEL=m
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
CONFIG_BRIDGE_NETFILTER=y

#
# Core Netfilter Configuration
#
CONFIG_NETFILTER_NETLINK=m
CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NETFILTER_NETLINK_LOG=m
CONFIG_NETFILTER_XTABLES=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
CONFIG_NETFILTER_XT_TARGET_MARK=m
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
CONFIG_NETFILTER_XT_MATCH_DCCP=m
CONFIG_NETFILTER_XT_MATCH_ESP=m
CONFIG_NETFILTER_XT_MATCH_HELPER=m
CONFIG_NETFILTER_XT_MATCH_LENGTH=m
CONFIG_NETFILTER_XT_MATCH_LIMIT=m
CONFIG_NETFILTER_XT_MATCH_MAC=m
CONFIG_NETFILTER_XT_MATCH_MARK=m
CONFIG_NETFILTER_XT_MATCH_POLICY=m
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
CONFIG_NETFILTER_XT_MATCH_PHYSDEV=m
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
CONFIG_NETFILTER_XT_MATCH_REALM=m
CONFIG_NETFILTER_XT_MATCH_SCTP=m
CONFIG_NETFILTER_XT_MATCH_STATE=m
CONFIG_NETFILTER_XT_MATCH_STRING=m
CONFIG_NETFILTER_XT_MATCH_TCPMSS=m

#
# IP: Netfilter Configuration
#
CONFIG_IP_NF_CONNTRACK=m
# CONFIG_IP_NF_CT_ACCT is not set
# CONFIG_IP_NF_CONNTRACK_MARK is not set
# CONFIG_IP_NF_CONNTRACK_EVENTS is not set
CONFIG_IP_NF_CONNTRACK_NETLINK=m
CONFIG_IP_NF_CT_PROTO_SCTP=m
CONFIG_IP_NF_FTP=m
CONFIG_IP_NF_IRC=m
CONFIG_IP_NF_NETBIOS_NS=m
CONFIG_IP_NF_TFTP=m
CONFIG_IP_NF_AMANDA=m
CONFIG_IP_NF_PPTP=m
CONFIG_IP_NF_H323=m
CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_IPRANGE=m
CONFIG_IP_NF_MATCH_TOS=m
CONFIG_IP_NF_MATCH_RECENT=m
CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_DSCP=m
CONFIG_IP_NF_MATCH_AH=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_MATCH_OWNER=m
CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_MATCH_HASHLIMIT=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_IP_NF_TARGET_TCPMSS=m
CONFIG_IP_NF_NAT=m
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_REDIRECT=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_SAME=m
CONFIG_IP_NF_NAT_SNMP_BASIC=m
CONFIG_IP_NF_NAT_IRC=m
CONFIG_IP_NF_NAT_FTP=m
CONFIG_IP_NF_NAT_TFTP=m
CONFIG_IP_NF_NAT_AMANDA=m
CONFIG_IP_NF_NAT_PPTP=m
CONFIG_IP_NF_NAT_H323=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_DSCP=m
CONFIG_IP_NF_TARGET_TTL=m
CONFIG_IP_NF_RAW=m
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m

#
# IPv6: Netfilter Configuration (EXPERIMENTAL)
#
CONFIG_IP6_NF_QUEUE=m
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_RT=m
CONFIG_IP6_NF_MATCH_OPTS=m
CONFIG_IP6_NF_MATCH_FRAG=m
CONFIG_IP6_NF_MATCH_HL=m
CONFIG_IP6_NF_MATCH_OWNER=m
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
CONFIG_IP6_NF_MATCH_AH=m
CONFIG_IP6_NF_MATCH_EUI64=m
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_LOG=m
CONFIG_IP6_NF_TARGET_REJECT=m
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_TARGET_HL=m
CONFIG_IP6_NF_RAW=m

#
# Bridge: Netfilter Configuration
#
CONFIG_BRIDGE_NF_EBTABLES=m
CONFIG_BRIDGE_EBT_BROUTE=m
CONFIG_BRIDGE_EBT_T_FILTER=m
CONFIG_BRIDGE_EBT_T_NAT=m
CONFIG_BRIDGE_EBT_802_3=m
CONFIG_BRIDGE_EBT_AMONG=m
CONFIG_BRIDGE_EBT_ARP=m
CONFIG_BRIDGE_EBT_IP=m
CONFIG_BRIDGE_EBT_LIMIT=m
CONFIG_BRIDGE_EBT_MARK=m
CONFIG_BRIDGE_EBT_PKTTYPE=m
CONFIG_BRIDGE_EBT_STP=m
CONFIG_BRIDGE_EBT_VLAN=m
CONFIG_BRIDGE_EBT_ARPREPLY=m
CONFIG_BRIDGE_EBT_DNAT=m
CONFIG_BRIDGE_EBT_MARK_T=m
CONFIG_BRIDGE_EBT_REDIRECT=m
CONFIG_BRIDGE_EBT_SNAT=m
CONFIG_BRIDGE_EBT_LOG=m
CONFIG_BRIDGE_EBT_ULOG=m

#
# DCCP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_DCCP is not set

#
# SCTP Configuration (EXPERIMENTAL)
#
CONFIG_IP_SCTP=m
# CONFIG_SCTP_DBG_messaggio is not set
# CONFIG_SCTP_DBG_OBJCNT is not set
# CONFIG_SCTP_HMAC_NONE is not set
# CONFIG_SCTP_HMAC_SHA1 is not set
CONFIG_SCTP_HMAC_MD5=y

#
# TIPC Configuration (EXPERIMENTAL)
#
# CONFIG_TIPC is not set
CONFIG_ATM=m
CONFIG_ATM_CLIP=m
# CONFIG_ATM_CLIP_NO_ICMP is not set
CONFIG_ATM_LANE=m
CONFIG_ATM_MPOA=m
CONFIG_ATM_BR2684=m
# CONFIG_ATM_BR2684_IPFILTER is not set
CONFIG_BRIDGE=m
CONFIG_VLAN_8021Q=m
# CONFIG_DECNET is not set
CONFIG_LLC=y
CONFIG_LLC2=m
CONFIG_IPX=m
# CONFIG_IPX_INTERN is not set
CONFIG_ATALK=m
CONFIG_DEV_APPLETALK=y
CONFIG_LTPC=m
CONFIG_COPS=m
CONFIG_COPS_DAYNA=y
CONFIG_COPS_TANGENT=y
CONFIG_IPDDP=m
CONFIG_IPDDP_ENCAP=y
CONFIG_IPDDP_DECAP=y
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
CONFIG_NET_DIVERT=y
# CONFIG_ECONET is not set
CONFIG_WAN_ROUTER=m

#
# QoS and/or fair queueing
#
CONFIG_NET_SCHED=y
CONFIG_NET_SCH_CLK_JIFFIES=y
# CONFIG_NET_SCH_CLK_GETTIMEOFDAY is not set
# CONFIG_NET_SCH_CLK_CPU is not set

#
# Queueing/Scheduling
#
CONFIG_NET_SCH_CBQ=m
CONFIG_NET_SCH_HTB=m
CONFIG_NET_SCH_HFSC=m
CONFIG_NET_SCH_ATM=m
CONFIG_NET_SCH_PRIO=m
CONFIG_NET_SCH_RED=m
CONFIG_NET_SCH_SFQ=m
CONFIG_NET_SCH_TEQL=m
CONFIG_NET_SCH_TBF=m
CONFIG_NET_SCH_GRED=m
CONFIG_NET_SCH_DSMARK=m
CONFIG_NET_SCH_NETEM=m
CONFIG_NET_SCH_INGRESS=m

#
# Classification
#
CONFIG_NET_CLS=y
CONFIG_NET_CLS_BASIC=m
CONFIG_NET_CLS_TCINDEX=m
CONFIG_NET_CLS_ROUTE4=m
CONFIG_NET_CLS_ROUTE=y
CONFIG_NET_CLS_FW=m
CONFIG_NET_CLS_U32=m
# CONFIG_CLS_U32_PERF is not set
CONFIG_CLS_U32_MARK=y
CONFIG_NET_CLS_RSVP=m
CONFIG_NET_CLS_RSVP6=m
# CONFIG_NET_EMATCH is not set
# CONFIG_NET_CLS_ACT is not set
CONFIG_NET_CLS_POLICE=y
# CONFIG_NET_CLS_IND is not set
CONFIG_NET_ESTIMATOR=y

#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
CONFIG_HAMRADIO=y

#
# Packet Radio protocols
#
CONFIG_AX25=m
# CONFIG_AX25_DAMA_SLAVE is not set
CONFIG_NETROM=m
CONFIG_ROSE=m

#
# AX.25 network device drivers
#
CONFIG_MKISS=m
CONFIG_6PACK=m
CONFIG_BPQETHER=m
CONFIG_DMASCC=m
CONFIG_SCC=m
CONFIG_SCC_DELAY=y
CONFIG_SCC_TRXECHO=y
CONFIG_BAYCOM_SER_FDX=m
CONFIG_BAYCOM_SER_HDX=m
CONFIG_BAYCOM_PAR=m
CONFIG_BAYCOM_EPP=m
CONFIG_YAM=m
CONFIG_IRDA=m

#
# IrDA protocols
#
CONFIG_IRLAN=m
CONFIG_IRNET=m
CONFIG_IRCOMM=m
# CONFIG_IRDA_ULTRA is not set

#
# IrDA options
#
CONFIG_IRDA_CACHE_LAST_LSAP=y
CONFIG_IRDA_FAST_RR=y
# CONFIG_IRDA_DEBUG is not set

#
# Infrared-port device drivers
#

#
# SIR device drivers
#
CONFIG_IRTTY_SIR=m

#
# Dongle support
#
CONFIG_DONGLE=y
CONFIG_ESI_DONGLE=m
CONFIG_ACTISYS_DONGLE=m
CONFIG_TEKRAM_DONGLE=m
CONFIG_TOIM3232_DONGLE=m
CONFIG_LITELINK_DONGLE=m
CONFIG_MA600_DONGLE=m
CONFIG_GIRBIL_DONGLE=m
CONFIG_MCP2120_DONGLE=m
CONFIG_OLD_BELKIN_DONGLE=m
CONFIG_ACT200L_DONGLE=m

#
# Old SIR device drivers
#
CONFIG_IRPORT_SIR=m

#
# Old Serial dongle support
#
# CONFIG_DONGLE_OLD is not set

#
# FIR device drivers
#
CONFIG_USB_IRDA=m
CONFIG_SIGMATEL_FIR=m
CONFIG_NSC_FIR=m
CONFIG_WINBOND_FIR=m
CONFIG_TOSHIBA_FIR=m
CONFIG_SMC_IRCC_FIR=m
CONFIG_ALI_FIR=m
CONFIG_VLSI_FIR=m
CONFIG_VIA_FIR=m
CONFIG_BT=m
CONFIG_BT_L2CAP=m
CONFIG_BT_SCO=m
CONFIG_BT_RFCOMM=m
CONFIG_BT_RFCOMM_TTY=y
CONFIG_BT_BNEP=m
CONFIG_BT_BNEP_MC_FILTER=y
CONFIG_BT_BNEP_PROTO_FILTER=y
CONFIG_BT_CMTP=m
CONFIG_BT_HIDP=m

#
# Bluetooth device drivers
#
CONFIG_BT_HCIUSB=m
CONFIG_BT_HCIUSB_SCO=y
CONFIG_BT_HCIUART=m
CONFIG_BT_HCIUART_H4=y
CONFIG_BT_HCIUART_BCSP=y
CONFIG_BT_HCIBCM203X=m
CONFIG_BT_HCIBPA10X=m
CONFIG_BT_HCIBFUSB=m
CONFIG_BT_HCIDTL1=m
CONFIG_BT_HCIBT3C=m
CONFIG_BT_HCIBLUECARD=m
CONFIG_BT_HCIBTUART=m
CONFIG_BT_HCIVHCI=m
CONFIG_IEEE80211=m
# CONFIG_IEEE80211_DEBUG is not set
CONFIG_IEEE80211_CRYPT_WEP=m
CONFIG_IEEE80211_CRYPT_CCMP=m
CONFIG_IEEE80211_CRYPT_TKIP=m
CONFIG_IEEE80211_SOFTMAC=m
# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set
CONFIG_WIRELESS_EXT=y

#
# Device Drivers
#

#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m

#
# Connector - unified userspace <-> kernelspace linker
#
CONFIG_CONNECTOR=m

#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set

#
# Parallel port support
#
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
CONFIG_PARPORT_SERIAL=m
# CONFIG_PARPORT_PC_FIFO is not set
# CONFIG_PARPORT_PC_SUPERIO is not set
CONFIG_PARPORT_PC_PCMCIA=m
CONFIG_PARPORT_NOT_PC=y
# CONFIG_PARPORT_GSC is not set
CONFIG_PARPORT_1284=y

#
# Plug and Play support
#
CONFIG_PNP=y
# CONFIG_PNP_DEBUG is not set

#
# Protocols
#
CONFIG_ISAPNP=y
# CONFIG_PNPBIOS is not set
# CONFIG_PNPACPI is not set

#
# Block devices
#
CONFIG_BLK_DEV_FD=y
CONFIG_BLK_DEV_.=m
CONFIG_PARIDE=m
CONFIG_PARIDE_PARPORT=m

#
# Parallel IDE high-level drivers
#
CONFIG_PARIDE_PD=m
CONFIG_PARIDE_PCD=m
CONFIG_PARIDE_PF=m
CONFIG_PARIDE_PT=m
CONFIG_PARIDE_PG=m

#
# Parallel IDE protocol modules
#
CONFIG_PARIDE_ATEN=m
CONFIG_PARIDE_BPCK=m
CONFIG_PARIDE_BPCK6=m
CONFIG_PARIDE_COMM=m
CONFIG_PARIDE_DSTR=m
CONFIG_PARIDE_FIT2=m
CONFIG_PARIDE_FIT3=m
CONFIG_PARIDE_EPAT=m
CONFIG_PARIDE_EPATC8=y
CONFIG_PARIDE_EPIA=m
CONFIG_PARIDE_FRIQ=m
CONFIG_PARIDE_FRPW=m
CONFIG_PARIDE_KBIC=m
CONFIG_PARIDE_KTTI=m
CONFIG_PARIDE_ON20=m
CONFIG_PARIDE_ON26=m
CONFIG_BLK_CPQ_DA=m
CONFIG_BLK_CPQ_CISS_DA=m
CONFIG_CISS_SCSI_TAPE=y
CONFIG_BLK_DEV_DAC960=m
CONFIG_BLK_DEV_UMEM=m
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_SX8=m
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=4096
CONFIG_BLK_DEV_INITRD=y
CONFIG_CDROM_PKTCDVD=m
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
CONFIG_ATA_OVER_ETH=m

#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y

#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
CONFIG_BLK_DEV_IDECS=m
CONFIG_BLK_DEV_IDECD=y
CONFIG_BLK_DEV_IDETAPE=m
CONFIG_BLK_DEV_IDEFLOPPY=y
CONFIG_BLK_DEV_IDESCSI=m
# CONFIG_IDE_TASK_IOCTL is not set

#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
# CONFIG_BLK_DEV_CMD640 is not set
CONFIG_BLK_DEV_IDEPNP=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
CONFIG_BLK_DEV_RZ1000=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
CONFIG_BLK_DEV_AEC62XX=y
CONFIG_BLK_DEV_ALI15X3=y
# CONFIG_WDC_ALI15X3 is not set
CONFIG_BLK_DEV_AMD74XX=y
CONFIG_BLK_DEV_ATIIXP=y
CONFIG_BLK_DEV_CMD64X=y
CONFIG_BLK_DEV_TRIFLEX=y
CONFIG_BLK_DEV_CY82C693=y
CONFIG_BLK_DEV_CS5520=y
CONFIG_BLK_DEV_CS5530=y
CONFIG_BLK_DEV_CS5535=y
CONFIG_BLK_DEV_HPT34X=y
# CONFIG_HPT34X_AUTODMA is not set
CONFIG_BLK_DEV_HPT366=y
# CONFIG_BLK_DEV_SC1200 is not set
CONFIG_BLK_DEV_PIIX=y
CONFIG_BLK_DEV_IT821X=y
# CONFIG_BLK_DEV_NS87415 is not set
CONFIG_BLK_DEV_PDC202XX_OLD=y
CONFIG_PDC202XX_BURST=y
CONFIG_BLK_DEV_PDC202XX_NEW=y
CONFIG_BLK_DEV_SVWKS=y
CONFIG_BLK_DEV_SIIMAGE=y
CONFIG_BLK_DEV_SIS5513=y
CONFIG_BLK_DEV_SLC90E66=y
CONFIG_BLK_DEV_TRM290=m
CONFIG_BLK_DEV_VIA82CXXX=y
# CONFIG_IDE_ARM is not set
CONFIG_IDE_CHIPSETS=y

#
# Note: most of these also require special kernel boot parameters
#
CONFIG_BLK_DEV_4DRIVES=y
CONFIG_BLK_DEV_ALI14XX=m
CONFIG_BLK_DEV_DTC2278=m
CONFIG_BLK_DEV_HT6560B=m
CONFIG_BLK_DEV_QD65XX=m
CONFIG_BLK_DEV_UMC8672=m
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set

#
# SCSI device support
#
CONFIG_RAID_ATTRS=m
CONFIG_SCSI=y
CONFIG_SCSI_PROC_FS=y

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
CONFIG_CHR_DEV_ST=m
CONFIG_CHR_DEV_OSST=m
CONFIG_BLK_DEV_SR=y
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m
CONFIG_CHR_DEV_SCH=m

#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set

#
# SCSI Transport Attributes
#
CONFIG_SCSI_SPI_ATTRS=m
CONFIG_SCSI_FC_ATTRS=m
CONFIG_SCSI_ISCSI_ATTRS=m
CONFIG_SCSI_SAS_ATTRS=m

#
# SCSI low-level drivers
#
CONFIG_ISCSI_TCP=m
CONFIG_BLK_DEV_3W_XXXX_RAID=m
CONFIG_SCSI_3W_9XXX=m
CONFIG_SCSI_7000FASST=m
CONFIG_SCSI_ACARD=m
CONFIG_SCSI_AHA152X=m
CONFIG_SCSI_AHA1542=m
CONFIG_SCSI_AACRAID=m
CONFIG_SCSI_AIC7XXX=m
CONFIG_AIC7XXX_CMDS_PER_DEVICE=32
CONFIG_AIC7XXX_RESET_DELAY_MS=5000
# CONFIG_AIC7XXX_DEBUG_ENABLE is not set
CONFIG_AIC7XXX_DEBUG_MASK=0
# CONFIG_AIC7XXX_REG_PRETTY_PRINT is not set
CONFIG_SCSI_AIC7XXX_OLD=m
CONFIG_SCSI_AIC79XX=m
CONFIG_AIC79XX_CMDS_PER_DEVICE=32
CONFIG_AIC79XX_RESET_DELAY_MS=5000
# CONFIG_AIC79XX_ENABLE_RD_STRM is not set
# CONFIG_AIC79XX_DEBUG_ENABLE is not set
CONFIG_AIC79XX_DEBUG_MASK=0
# CONFIG_AIC79XX_REG_PRETTY_PRINT is not set
CONFIG_SCSI_DPT_I2O=m
CONFIG_SCSI_ADVANSYS=m
CONFIG_SCSI_IN2000=m
CONFIG_MEGARAID_NEWGEN=y
CONFIG_MEGARAID_MM=m
CONFIG_MEGARAID_MAILBOX=m
CONFIG_MEGARAID_LEGACY=m
CONFIG_MEGARAID_SAS=m
CONFIG_SCSI_SATA=y
CONFIG_SCSI_SATA_AHCI=m
CONFIG_SCSI_SATA_SVW=m
CONFIG_SCSI_ATA_PIIX=m
CONFIG_SCSI_SATA_MV=m
CONFIG_SCSI_SATA_NV=m
CONFIG_SCSI_PDC_ADMA=m
CONFIG_SCSI_SATA_QSTOR=m
CONFIG_SCSI_SATA_PROMISE=m
CONFIG_SCSI_SATA_SX4=m
CONFIG_SCSI_SATA_SIL=m
CONFIG_SCSI_SATA_SIL24=m
CONFIG_SCSI_SATA_SIS=m
CONFIG_SCSI_SATA_ULI=m
CONFIG_SCSI_SATA_VIA=m
CONFIG_SCSI_SATA_VITESSE=m
CONFIG_SCSI_SATA_INTEL_COMBINED=y
CONFIG_SCSI_BUSLOGIC=m
# CONFIG_SCSI_OMIT_FLASHPOINT is not set
CONFIG_SCSI_DMX3191D=m
CONFIG_SCSI_DTC3280=m
CONFIG_SCSI_EATA=m
# CONFIG_SCSI_EATA_TAGGED_QUEUE is not set
# CONFIG_SCSI_EATA_LINKED_COMMANDS is not set
CONFIG_SCSI_EATA_MAX_TAGS=16
CONFIG_SCSI_FUTURE_DOMAIN=m
CONFIG_SCSI_GDTH=m
CONFIG_SCSI_GENERIC_NCR5380=m
CONFIG_SCSI_GENERIC_NCR5380_MMIO=m
CONFIG_SCSI_GENERIC_NCR53C400=y
CONFIG_SCSI_IPS=m
CONFIG_SCSI_INITIO=m
CONFIG_SCSI_INIA100=m
CONFIG_SCSI_PPA=m
CONFIG_SCSI_IMM=m
# CONFIG_SCSI_IZIP_EPP16 is not set
# CONFIG_SCSI_IZIP_SLOW_CTR is not set
CONFIG_SCSI_NCR53C406A=m
CONFIG_SCSI_SYM53C8XX_2=m
CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1
CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16
CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64
CONFIG_SCSI_SYM53C8XX_MMIO=y
CONFIG_SCSI_IPR=m
# CONFIG_SCSI_IPR_TRACE is not set
# CONFIG_SCSI_IPR_DUMP is not set
CONFIG_SCSI_PAS16=m
CONFIG_SCSI_PSI240I=m
CONFIG_SCSI_QLOGIC_FAS=m
CONFIG_SCSI_QLOGIC_1280=m
CONFIG_SCSI_QLA_FC=m
# CONFIG_SCSI_QLA2XXX_EMBEDDED_FIRMWARE is not set
CONFIG_SCSI_LPFC=m
CONFIG_SCSI_SYM53C416=m
CONFIG_SCSI_DC395x=m
CONFIG_SCSI_DC390T=m
CONFIG_SCSI_T128=m
CONFIG_SCSI_U14_34F=m
# CONFIG_SCSI_U14_34F_TAGGED_QUEUE is not set
# CONFIG_SCSI_U14_34F_LINKED_COMMANDS is not set
CONFIG_SCSI_U14_34F_MAX_TAGS=8
CONFIG_SCSI_ULTRASTOR=m
CONFIG_SCSI_NSP32=m
CONFIG_SCSI_DEBUG=m

#
# PCMCIA SCSI adapter support
#
CONFIG_PCMCIA_AHA152X=m
CONFIG_PCMCIA_FDOMAIN=m
CONFIG_PCMCIA_NINJA_SCSI=m
CONFIG_PCMCIA_QLOGIC=m
CONFIG_PCMCIA_SYM53C500=m

#
# Old CD-ROM drivers (not SCSI, not IDE)
#
CONFIG_CD_NO_IDESCSI=y
CONFIG_AZTCD=m
CONFIG_GSCD=m
CONFIG_SBPCD=m
CONFIG_MCDX=m
CONFIG_OPTCD=m
CONFIG_CM206=m
CONFIG_SJCD=m
CONFIG_ISP16_CDI=m
CONFIG_CDU31A=m
CONFIG_CDU535=m

#
# Multi-device support (RAID and LVM)
#
CONFIG_MD=y
CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
CONFIG_MD_RAID0=m
CONFIG_MD_RAID1=m
CONFIG_MD_RAID10=m
CONFIG_MD_RAID5=m
CONFIG_MD_RAID5_RESHAPE=y
CONFIG_MD_RAID6=m
CONFIG_MD_MULTIPATH=m
CONFIG_MD_FAULTY=m
CONFIG_BLK_DEV_DM=m
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=m
CONFIG_DM_MIRROR=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
CONFIG_DM_MULTIPATH_EMC=m

#
# Fusion MPT device support
#
CONFIG_FUSION=y
CONFIG_FUSION_SPI=m
CONFIG_FUSION_FC=m
CONFIG_FUSION_SAS=m
CONFIG_FUSION_MAX_SGE=128
CONFIG_FUSION_CTL=m
CONFIG_FUSION_LAN=m

#
# IEEE 1394 (FireWire) support
#
CONFIG_IEEE1394=m

#
# Subsystem Options
#
# CONFIG_IEEE1394_VERBOSEDEBUG is not set
# CONFIG_IEEE1394_OUI_DB is not set
CONFIG_IEEE1394_EXTRA_CONFIG_ROMS=y
CONFIG_IEEE1394_CONFIG_ROM_IP1394=y
# CONFIG_IEEE1394_EXPORT_FULL_API is not set

#
# Device Drivers
#
CONFIG_IEEE1394_PCILYNX=m
CONFIG_IEEE1394_OHCI1394=m

#
# Protocol Drivers
#
CONFIG_IEEE1394_VIDEO1394=m
CONFIG_IEEE1394_SBP2=m
# CONFIG_IEEE1394_SBP2_PHYS_DMA is not set
CONFIG_IEEE1394_ETH1394=m
CONFIG_IEEE1394_DV1394=m
CONFIG_IEEE1394_RAWIO=m

#
# I2O device support
#
CONFIG_I2O=m
CONFIG_I2O_LCT_NOTIFY_ON_CHANGES=y
CONFIG_I2O_EXT_ADAPTEC=y
CONFIG_I2O_CONFIG=m
CONFIG_I2O_CONFIG_OLD_IOCTL=y
CONFIG_I2O_BUS=m
CONFIG_I2O_BLOCK=m
CONFIG_I2O_SCSI=m
CONFIG_I2O_PROC=m

#
# Network device support
#
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
CONFIG_BONDING=m
CONFIG_EQUALIZER=m
CONFIG_TUN=m
CONFIG_NET_SB1000=m

#
# ARCnet devices
#
CONFIG_ARCNET=m
CONFIG_ARCNET_1201=m
CONFIG_ARCNET_1051=m
CONFIG_ARCNET_RAW=m
CONFIG_ARCNET_CAP=m
CONFIG_ARCNET_COM90xx=m
CONFIG_ARCNET_COM90xxIO=m
CONFIG_ARCNET_RIM_I=m
CONFIG_ARCNET_COM20020=m
CONFIG_ARCNET_COM20020_ISA=m
CONFIG_ARCNET_COM20020_PCI=m

#
# PHY device support
#
CONFIG_PHYLIB=m

#
# MII PHY device drivers
#
CONFIG_MARVELL_PHY=m
CONFIG_DAVICOM_PHY=m
CONFIG_QSEMI_PHY=m
CONFIG_LXT_PHY=m
CONFIG_CICADA_PHY=m

#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=m
CONFIG_HAPPYMEAL=m
CONFIG_SUNGEM=m
CONFIG_CASSINI=m
CONFIG_NET_VENDOR_3COM=y
CONFIG_EL1=m
CONFIG_EL2=m
CONFIG_ELPLUS=m
CONFIG_EL16=m
CONFIG_EL3=m
CONFIG_3C515=m
CONFIG_VORTEX=m
CONFIG_TYPHOON=m
CONFIG_LANCE=m
CONFIG_NET_VENDOR_SMC=y
CONFIG_WD80x3=m
CONFIG_ULTRA=m
CONFIG_SMC9194=m
CONFIG_NET_VENDOR_RACAL=y
CONFIG_NI5010=m
CONFIG_NI52=m
CONFIG_NI65=m

#
# Tulip family network device support
#
CONFIG_NET_TULIP=y
CONFIG_DE2104X=m
CONFIG_TULIP=m
# CONFIG_TULIP_MWI is not set
CONFIG_TULIP_MMIO=y
# CONFIG_TULIP_NAPI is not set
CONFIG_DE4X5=m
CONFIG_WINBOND_840=m
CONFIG_DM9102=m
CONFIG_ULI526X=m
CONFIG_PCMCIA_XIRCOM=m
CONFIG_PCMCIA_XIRTULIP=m
CONFIG_AT1700=m
CONFIG_DEPCA=m
CONFIG_HP100=m
CONFIG_NET_ISA=y
CONFIG_E2100=m
CONFIG_EWRK3=m
CONFIG_EEXPRESS=m
CONFIG_EEXPRESS_PRO=m
CONFIG_HPLAN_PLUS=m
CONFIG_HPLAN=m
CONFIG_LP486E=m
CONFIG_ETH16I=m
CONFIG_NE2000=m
CONFIG_ZNET=m
CONFIG_SEEQ8005=m
CONFIG_NET_PCI=y
CONFIG_PCNET32=m
CONFIG_AMD8111_ETH=m
# CONFIG_AMD8111E_NAPI is not set
CONFIG_ADAPTEC_STARFIRE=m
CONFIG_ADAPTEC_STARFIRE_NAPI=y
CONFIG_AC3200=m
CONFIG_APRICOT=m
CONFIG_B44=m
CONFIG_FORCEDETH=m
CONFIG_CS89x0=m
CONFIG_DGRS=m
CONFIG_EEPRO100=m
CONFIG_E100=m
CONFIG_FEALNX=m
CONFIG_NATSEMI=m
CONFIG_NE2K_PCI=m
CONFIG_8139CP=m
CONFIG_8139TOO=m
CONFIG_8139TOO_PIO=y
# CONFIG_8139TOO_TUNE_TWISTER is not set
CONFIG_8139TOO_8129=y
# CONFIG_8139_OLD_RX_RESET is not set
CONFIG_SIS900=m
CONFIG_EPIC100=m
CONFIG_SUNDANCE=m
# CONFIG_SUNDANCE_MMIO is not set
CONFIG_TLAN=m
CONFIG_VIA_RHINE=m
CONFIG_VIA_RHINE_MMIO=y
CONFIG_NET_POCKET=y
CONFIG_ATP=m
CONFIG_DE600=m
CONFIG_DE620=m

#
# Ethernet (1000 Mbit)
#
CONFIG_ACENIC=m
# CONFIG_ACENIC_OMIT_TIGON_I is not set
CONFIG_DL2K=m
CONFIG_E1000=m
CONFIG_E1000_NAPI=y
# CONFIG_E1000_DISABLE_PACKET_SPLIT is not set
CONFIG_NS83820=m
CONFIG_HAMACHI=m
CONFIG_YELLOWFIN=m
CONFIG_R8169=m
# CONFIG_R8169_NAPI is not set
CONFIG_R8169_VLAN=y
CONFIG_SIS190=m
CONFIG_SKGE=m
CONFIG_SKY2=m
CONFIG_SK98LIN=m
CONFIG_VIA_VELOCITY=m
CONFIG_TIGON3=m
CONFIG_BNX2=m

#
# Ethernet (10000 Mbit)
#
CONFIG_CHELSIO_T1=m
CONFIG_IXGB=m
CONFIG_IXGB_NAPI=y
CONFIG_S2IO=m
# CONFIG_S2IO_NAPI is not set

#
# Token Ring devices
#
CONFIG_TR=y
CONFIG_IBMTR=m
CONFIG_IBMOL=m
CONFIG_IBMLS=m
CONFIG_3C359=m
CONFIG_TMS380TR=m
CONFIG_TMSPCI=m
CONFIG_SKISA=m
CONFIG_PROTEON=m
CONFIG_ABYSS=m
CONFIG_SMCTR=m

#
# Wireless LAN (non-hamradio)
#
CONFIG_NET_RADIO=y
CONFIG_NET_WIRELESS_RTNETLINK=y

#
# Obsolete Wireless cards support (pre-802.11)
#
CONFIG_STRIP=m
CONFIG_ARLAN=m
CONFIG_WAVELAN=m
CONFIG_PCMCIA_WAVELAN=m
CONFIG_PCMCIA_NETWAVE=m

#
# Wireless 802.11 Frequency Hopping cards support
#
CONFIG_PCMCIA_RAYCS=m

#
# Wireless 802.11b ISA/PCI cards support
#
CONFIG_IPW2100=m
CONFIG_IPW2100_MONITOR=y
# CONFIG_IPW2100_DEBUG is not set
CONFIG_IPW2200=m
CONFIG_IPW2200_MONITOR=y
CONFIG_IPW_QOS=y
# CONFIG_IPW2200_DEBUG is not set
CONFIG_AIRO=m
CONFIG_HERMES=m
CONFIG_PLX_HERMES=m
CONFIG_TMD_HERMES=m
CONFIG_NORTEL_HERMES=m
CONFIG_PCI_HERMES=m
CONFIG_ATMEL=m
CONFIG_PCI_ATMEL=m

#
# Wireless 802.11b Pcmcia/Cardbus cards support
#
CONFIG_PCMCIA_HERMES=m
CONFIG_PCMCIA_SPECTRUM=m
CONFIG_AIRO_CS=m
CONFIG_PCMCIA_ATMEL=m
CONFIG_PCMCIA_WL3501=m

#
# Prism GT/Duette 802.11(a/b/g) PCI/Cardbus support
#
CONFIG_PRISM54=m
CONFIG_HOSTAP=m
CONFIG_HOSTAP_FIRMWARE=y
CONFIG_HOSTAP_FIRMWARE_NVRAM=y
CONFIG_HOSTAP_PLX=m
CONFIG_HOSTAP_PCI=m
CONFIG_HOSTAP_CS=m
CONFIG_BCM43XX=m
CONFIG_BCM43XX_DEBUG=y
CONFIG_BCM43XX_DMA=y
CONFIG_BCM43XX_PIO=y
CONFIG_BCM43XX_DMA_AND_PIO_MODE=y
# CONFIG_BCM43XX_DMA_MODE is not set
# CONFIG_BCM43XX_PIO_MODE is not set
CONFIG_NET_WIRELESS=y

#
# PCMCIA network device support
#
CONFIG_NET_PCMCIA=y
CONFIG_PCMCIA_3C589=m
CONFIG_PCMCIA_3C574=m
CONFIG_PCMCIA_FMVJ18X=m
CONFIG_PCMCIA_PCNET=m
CONFIG_PCMCIA_NMCLAN=m
CONFIG_PCMCIA_SMC91C92=m
CONFIG_PCMCIA_XIRC2PS=m
CONFIG_PCMCIA_AXNET=m
CONFIG_ARCNET_COM20020_CS=m
CONFIG_PCMCIA_IBMTR=m

#
# Wan interfaces
#
CONFIG_WAN=y
CONFIG_HOSTESS_SV11=m
CONFIG_COSA=m
CONFIG_DSCC4=m
# CONFIG_DSCC4_PCISYNC is not set
# CONFIG_DSCC4_PCI_RST is not set
CONFIG_LANMEDIA=m
CONFIG_SEALEVEL_4021=m
CONFIG_SYNCLINK_SYNCPPP=m
CONFIG_HDLC=m
CONFIG_HDLC_RAW=y
CONFIG_HDLC_RAW_ETH=y
CONFIG_HDLC_CISCO=y
CONFIG_HDLC_FR=y
CONFIG_HDLC_PPP=y

#
# X.25/LAPB support is disabled
#
CONFIG_PCI200SYN=m
CONFIG_WANXL=m
CONFIG_PC300=m
# CONFIG_PC300_MLPPP is not set
CONFIG_N2=m
CONFIG_C101=m
CONFIG_FARSYNC=m
CONFIG_DLCI=m
CONFIG_DLCI_COUNT=24
CONFIG_DLCI_MAX=8
CONFIG_SDLA=m
CONFIG_WAN_ROUTER_DRIVERS=y
CONFIG_CYCLADES_SYNC=m
CONFIG_CYCLOMX_X25=y
CONFIG_SBNI=m
# CONFIG_SBNI_MULTILINE is not set

#
# ATM drivers
#
CONFIG_ATM_DUMMY=m
CONFIG_ATM_TCP=m
CONFIG_ATM_LANAI=m
CONFIG_ATM_ENI=m
# CONFIG_ATM_ENI_DEBUG is not set
# CONFIG_ATM_ENI_TUNE_BURST is not set
CONFIG_ATM_FIRESTREAM=m
CONFIG_ATM_ZATM=m
# CONFIG_ATM_ZATM_DEBUG is not set
CONFIG_ATM_NICSTAR=m
# CONFIG_ATM_NICSTAR_USE_SUNI is not set
# CONFIG_ATM_NICSTAR_USE_IDT77105 is not set
CONFIG_ATM_IDT77252=m
# CONFIG_ATM_IDT77252_DEBUG is not set
# CONFIG_ATM_IDT77252_RCV_ALL is not set
CONFIG_ATM_IDT77252_USE_SUNI=y
CONFIG_ATM_AMBASSADOR=m
# CONFIG_ATM_AMBASSADOR_DEBUG is not set
CONFIG_ATM_HORIZON=m
# CONFIG_ATM_HORIZON_DEBUG is not set
CONFIG_ATM_IA=m
# CONFIG_ATM_IA_DEBUG is not set
CONFIG_ATM_FORE200E_MAYBE=m
# CONFIG_ATM_FORE200E_PCA is not set
CONFIG_ATM_HE=m
# CONFIG_ATM_HE_USE_SUNI is not set
CONFIG_FDDI=y
CONFIG_DEFXX=m
CONFIG_SKFP=m
CONFIG_HIPPI=y
CONFIG_ROADRUNNER=m
# CONFIG_ROADRUNNER_LARGE_RINGS is not set
CONFIG_PLIP=m
CONFIG_PPP=m
CONFIG_PPP_MULTILINK=y
CONFIG_PPP_FILTER=y
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
CONFIG_PPP_MPPE=m
CONFIG_PPPOE=m
CONFIG_PPPOATM=m
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLIP_SMART=y
# CONFIG_SLIP_MODE_SLIP6 is not set
CONFIG_NET_FC=y
CONFIG_SHAPER=m
CONFIG_NETCONSOLE=m
CONFIG_NETPOLL=y
# CONFIG_NETPOLL_RX is not set
# CONFIG_NETPOLL_TRAP is not set
CONFIG_NET_POLL_CONTROLLER=y

#
# ISDN subsystem
#
CONFIG_ISDN=m

#
# Old ISDN4Linux
#
CONFIG_ISDN_I4L=m
CONFIG_ISDN_PPP=y
CONFIG_ISDN_PPP_VJ=y
CONFIG_ISDN_MPP=y
CONFIG_IPPP_FILTER=y
CONFIG_ISDN_PPP_BSDCOMP=m
CONFIG_ISDN_AUDIO=y
CONFIG_ISDN_TTY_FAX=y

#
# ISDN feature submodules
#
CONFIG_ISDN_DRV_LOOP=m
CONFIG_ISDN_DIVERSION=m

#
# ISDN4Linux hardware drivers
#

#
# Passive cards
#
CONFIG_ISDN_DRV_HISAX=m

#
# D-channel protocol features
#
CONFIG_HISAX_EURO=y
CONFIG_DE_AOC=y
CONFIG_HISAX_NO_SENDCOMPLETE=y
CONFIG_HISAX_NO_LLC=y
CONFIG_HISAX_NO_KEYPAD=y
CONFIG_HISAX_1TR6=y
CONFIG_HISAX_NI1=y
CONFIG_HISAX_MAX_CARDS=8

#
# HiSax supported cards
#
CONFIG_HISAX_16_0=y
CONFIG_HISAX_16_3=y
CONFIG_HISAX_TELESPCI=y
CONFIG_HISAX_S0BOX=y
CONFIG_HISAX_AVM_A1=y
CONFIG_HISAX_FRITZPCI=y
CONFIG_HISAX_AVM_A1_PCMCIA=y
CONFIG_HISAX_ELSA=y
CONFIG_HISAX_IX1MICROR2=y
CONFIG_HISAX_DIEHLDIVA=y
CONFIG_HISAX_ASUSCOM=y
CONFIG_HISAX_TELEINT=y
CONFIG_HISAX_HFCS=y
CONFIG_HISAX_SEDLBAUER=y
CONFIG_HISAX_SPORTSTER=y
CONFIG_HISAX_MIC=y
CONFIG_HISAX_NETJET=y
CONFIG_HISAX_NETJET_U=y
CONFIG_HISAX_NICCY=y
CONFIG_HISAX_ISURF=y
CONFIG_HISAX_HSTSAPHIR=y
CONFIG_HISAX_BKM_A4T=y
CONFIG_HISAX_SCT_QUADRO=y
CONFIG_HISAX_GAZEL=y
CONFIG_HISAX_HFC_PCI=y
CONFIG_HISAX_W6692=y
CONFIG_HISAX_HFC_SX=y
CONFIG_HISAX_ENTERNOW_PCI=y
# CONFIG_HISAX_DEBUG is not set

#
# HiSax PCMCIA card service modules
#
CONFIG_HISAX_SEDLBAUER_CS=m
CONFIG_HISAX_ELSA_CS=m
CONFIG_HISAX_AVM_A1_CS=m
CONFIG_HISAX_TELES_CS=m

#
# HiSax sub driver modules
#
CONFIG_HISAX_ST5481=m
CONFIG_HISAX_HFCUSB=m
CONFIG_HISAX_HFC4S8S=m
CONFIG_HISAX_FRITZ_PCIPNP=m
CONFIG_HISAX_HDLC=y

#
# Active cards
#
CONFIG_ISDN_DRV_ICN=m
CONFIG_ISDN_DRV_PCBIT=m
CONFIG_ISDN_DRV_SC=m
CONFIG_ISDN_DRV_ACT2000=m
CONFIG_HYSDN=m
CONFIG_HYSDN_CAPI=y

#
# Siemens Gigaset
#
CONFIG_ISDN_DRV_GIGASET=m
CONFIG_GIGASET_BASE=m
CONFIG_GIGASET_M105=m
# CONFIG_GIGASET_DEBUG is not set
# CONFIG_GIGASET_UNDOCREQ is not set

#
# CAPI subsystem
#
CONFIG_ISDN_CAPI=m
CONFIG_ISDN_DRV_AVMB1_VERBOSE_REASON=y
CONFIG_ISDN_CAPI_MIDDLEWARE=y
CONFIG_ISDN_CAPI_CAPI20=m
CONFIG_ISDN_CAPI_CAPIFS_BOOL=y
CONFIG_ISDN_CAPI_CAPIFS=m
CONFIG_ISDN_CAPI_CAPIDRV=m

#
# CAPI hardware drivers
#

#
# Active AVM cards
#
CONFIG_CAPI_AVM=y
CONFIG_ISDN_DRV_AVMB1_B1ISA=m
CONFIG_ISDN_DRV_AVMB1_B1PCI=m
CONFIG_ISDN_DRV_AVMB1_B1PCIV4=y
CONFIG_ISDN_DRV_AVMB1_T1ISA=m
CONFIG_ISDN_DRV_AVMB1_B1PCMCIA=m
CONFIG_ISDN_DRV_AVMB1_AVM_CS=m
CONFIG_ISDN_DRV_AVMB1_T1PCI=m
CONFIG_ISDN_DRV_AVMB1_C4=m

#
# Active Eicon DIVA Server cards
#
CONFIG_CAPI_EICON=y
CONFIG_ISDN_DIVAS=m
CONFIG_ISDN_DIVAS_BRIPCI=y
CONFIG_ISDN_DIVAS_PRIPCI=y
CONFIG_ISDN_DIVAS_DIVACAPI=m
CONFIG_ISDN_DIVAS_USERIDI=m
CONFIG_ISDN_DIVAS_MAINT=m

#
# Telephony Support
#
CONFIG_PHONE=m
CONFIG_PHONE_IXJ=m
CONFIG_PHONE_IXJ_PCMCIA=m

#
# Input device support
#
CONFIG_INPUT=y

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
CONFIG_INPUT_JOYDEV=m
# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=m
# CONFIG_INPUT_EVBUG is not set

#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=m
CONFIG_MOUSE_SERIAL=m
CONFIG_MOUSE_INPORT=m
CONFIG_MOUSE_ATIXL=y
CONFIG_MOUSE_LOGIBM=m
CONFIG_MOUSE_PC110PAD=m
CONFIG_MOUSE_VSXXXAA=m
CONFIG_INPUT_JOYSTICK=y
CONFIG_JOYSTICK_ANALOG=m
CONFIG_JOYSTICK_A3D=m
CONFIG_JOYSTICK_ADI=m
CONFIG_JOYSTICK_COBRA=m
CONFIG_JOYSTICK_GF2K=m
CONFIG_JOYSTICK_GRIP=m
CONFIG_JOYSTICK_GRIP_MP=m
CONFIG_JOYSTICK_GUILLEMOT=m
CONFIG_JOYSTICK_INTERACT=m
CONFIG_JOYSTICK_SIDEWINDER=m
CONFIG_JOYSTICK_TMDC=m
CONFIG_JOYSTICK_IFORCE=m
CONFIG_JOYSTICK_IFORCE_USB=y
CONFIG_JOYSTICK_IFORCE_232=y
CONFIG_JOYSTICK_WARRIOR=m
CONFIG_JOYSTICK_MAGELLAN=m
CONFIG_JOYSTICK_SPACEORB=m
CONFIG_JOYSTICK_SPACEBALL=m
CONFIG_JOYSTICK_STINGER=m
CONFIG_JOYSTICK_TWIDJOY=m
CONFIG_JOYSTICK_DB9=m
CONFIG_JOYSTICK_GAMECON=m
CONFIG_JOYSTICK_TURBOGRAFX=m
CONFIG_JOYSTICK_JOYDUMP=m
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_TOUCHSCREEN_GUNZE=m
CONFIG_TOUCHSCREEN_ELO=m
CONFIG_TOUCHSCREEN_MTOUCH=m
CONFIG_TOUCHSCREEN_MK712=m
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=m
CONFIG_INPUT_WISTRON_BTNS=m
CONFIG_INPUT_UINPUT=m

#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=m
CONFIG_SERIO_CT82C710=m
CONFIG_SERIO_PARKBD=m
CONFIG_SERIO_PCIPS2=m
CONFIG_SERIO_LIBPS2=y
CONFIG_SERIO_RAW=m
CONFIG_GAMEPORT=m
CONFIG_GAMEPORT_NS558=m
CONFIG_GAMEPORT_L4=m
CONFIG_GAMEPORT_EMU10K1=m
CONFIG_GAMEPORT_FM801=m

#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_SERIAL_NONSTANDARD=y
CONFIG_COMPUTONE=m
CONFIG_ROCKETPORT=m
CONFIG_CYCLADES=m
# CONFIG_CYZ_INTR is not set
CONFIG_DIGIEPCA=m
CONFIG_ESPSERIAL=m
CONFIG_MOXA_INTELLIO=m
CONFIG_MOXA_SMARTIO=m
CONFIG_ISI=m
CONFIG_SYNCLINK=m
CONFIG_SYNCLINKMP=m
CONFIG_SYNCLINK_GT=m
CONFIG_N_HDLC=m
CONFIG_RISCOM8=m
CONFIG_SPECIALIX=m
# CONFIG_SPECIALIX_RTSCTS is not set
CONFIG_SX=m
CONFIG_RIO=m
# CONFIG_RIO_OLDPCI is not set
CONFIG_STALDRV=y
CONFIG_STALLION=m
CONFIG_ISTALLION=m

#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_PCI=y
CONFIG_SERIAL_8250_PNP=y
CONFIG_SERIAL_8250_CS=m
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
CONFIG_SERIAL_8250_DETECT_IRQ=y
CONFIG_SERIAL_8250_RSA=y
CONFIG_SERIAL_8250_FOURPORT=m
CONFIG_SERIAL_8250_ACCENT=m
CONFIG_SERIAL_8250_BOCA=m
CONFIG_SERIAL_8250_HUB6=m

#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_SERIAL_JSM=m
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
CONFIG_PRINTER=m
CONFIG_LP_CONSOLE=y
CONFIG_PPDEV=m
CONFIG_TIPAR=m

#
# IPMI
#
CONFIG_IPMI_HANDLER=m
# CONFIG_IPMI_PANIC_EVENT is not set
CONFIG_IPMI_DEVICE_INTERFACE=m
CONFIG_IPMI_SI=m
CONFIG_IPMI_WATCHDOG=m
CONFIG_IPMI_POWEROFF=m

#
# Watchdog Cards
#
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set

#
# Watchdog Device Drivers
#
CONFIG_SOFT_WATCHDOG=m
CONFIG_ACQUIRE_WDT=m
CONFIG_ADVANTECH_WDT=m
CONFIG_ALIM1535_WDT=m
CONFIG_ALIM7101_WDT=m
CONFIG_SC520_WDT=m
CONFIG_EUROTECH_WDT=m
CONFIG_IB700_WDT=m
CONFIG_IBMASR=m
CONFIG_WAFER_WDT=m
CONFIG_I6300ESB_WDT=m
CONFIG_I8XX_TCO=m
CONFIG_SC1200_WDT=m
CONFIG_SCx200_WDT=m
CONFIG_60XX_WDT=m
CONFIG_SBC8360_WDT=m
CONFIG_CPU5_WDT=m
CONFIG_W83627HF_WDT=m
CONFIG_W83877F_WDT=m
CONFIG_W83977F_WDT=m
CONFIG_MACHZ_WDT=m
CONFIG_SBC_EPX_C3_WATCHDOG=m

#
# ISA-based Watchdog Cards
#
CONFIG_PCWATCHDOG=m
CONFIG_MIXCOMWD=m
CONFIG_WDT=m
# CONFIG_WDT_501 is not set

#
# PCI-based Watchdog Cards
#
CONFIG_PCIPCWATCHDOG=m
CONFIG_WDTPCI=m
CONFIG_WDT_501_PCI=y

#
# USB-based Watchdog Cards
#
CONFIG_USBPCWATCHDOG=m
CONFIG_HW_RANDOM=m
CONFIG_NVRAM=m
CONFIG_RTC=y
CONFIG_DTLK=m
CONFIG_R3964=m
CONFIG_APPLICOM=m
CONFIG_SONYPI=m

#
# Ftape, the floppy tape device driver
#
CONFIG_FTAPE=m
CONFIG_ZFTAPE=m
CONFIG_ZFT_DFLT_BLK_SZ=10240

#
# The compressor will be built as a module only!
#
CONFIG_ZFT_COMPRESSOR=m
CONFIG_FT_NR_BUFFERS=3
# CONFIG_FT_PROC_FS is not set
CONFIG_FT_NORMAL_DEBUG=y
# CONFIG_FT_FULL_DEBUG is not set
# CONFIG_FT_NO_TRACE is not set
# CONFIG_FT_NO_TRACE_AT_ALL is not set

#
# Hardware configuration
#
CONFIG_FT_STD_FDC=y
# CONFIG_FT_MACH2 is not set
# CONFIG_FT_PROBE_FC10 is not set
# CONFIG_FT_ALT_FDC is not set
CONFIG_FT_FDC_THR=8
CONFIG_FT_FDC_MAX_RATE=2000
CONFIG_FT_ALPHA_CLOCK=0
CONFIG_AGP=m
CONFIG_AGP_ALI=m
CONFIG_AGP_ATI=m
CONFIG_AGP_AMD=m
CONFIG_AGP_AMD64=m
CONFIG_AGP_INTEL=m
CONFIG_AGP_NVIDIA=m
CONFIG_AGP_SIS=m
CONFIG_AGP_SWORKS=m
CONFIG_AGP_VIA=m
CONFIG_AGP_EFFICEON=m
CONFIG_DRM=m
CONFIG_DRM_TDFX=m
CONFIG_DRM_R128=m
CONFIG_DRM_RADEON=m
CONFIG_DRM_I810=m
CONFIG_DRM_I830=m
CONFIG_DRM_I915=m
CONFIG_DRM_MGA=m
CONFIG_DRM_SIS=m
CONFIG_DRM_VIA=m
CONFIG_DRM_SAVAGE=m

#
# PCMCIA character devices
#
CONFIG_SYNCLINK_CS=m
CONFIG_CARDMAN_4000=m
CONFIG_CARDMAN_4040=m
CONFIG_MWAVE=m
CONFIG_SCx200_GPIO=m
CONFIG_CS5535_GPIO=m
# CONFIG_RAW_DRIVER is not set
# CONFIG_HPET is not set
CONFIG_HANGCHECK_TIMER=m

#
# TPM devices
#
CONFIG_TCG_TPM=m
CONFIG_TCG_ATMEL=m
CONFIG_TELCLOCK=m

#
# I2C support
#
CONFIG_I2C=m
CONFIG_I2C_CHARDEV=m

#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=m
CONFIG_I2C_ALGOPCF=m
CONFIG_I2C_ALGOPCA=m

#
# I2C Hardware Bus support
#
CONFIG_I2C_ALI1535=m
CONFIG_I2C_ALI1563=m
CONFIG_I2C_ALI15X3=m
CONFIG_I2C_AMD756=m
CONFIG_I2C_AMD756_S4882=m
CONFIG_I2C_AMD8111=m
CONFIG_I2C_ELEKTOR=m
CONFIG_I2C_I801=m
CONFIG_I2C_I810=m
CONFIG_I2C_PIIX4=m
CONFIG_I2C_ISA=m
CONFIG_I2C_NFORCE2=m
CONFIG_I2C_PARPORT=m
CONFIG_I2C_PARPORT_LIGHT=m
CONFIG_I2C_PROSAVAGE=m
CONFIG_I2C_SAVAGE4=m
CONFIG_SCx200_I2C=m
CONFIG_SCx200_I2C_SCL=12
CONFIG_SCx200_I2C_SDA=13
CONFIG_SCx200_ACB=m
CONFIG_I2C_SIS5595=m
CONFIG_I2C_SIS630=m
CONFIG_I2C_SIS96X=m
CONFIG_I2C_STUB=m
CONFIG_I2C_VIA=m
CONFIG_I2C_VIAPRO=m
CONFIG_I2C_VOODOO3=m
CONFIG_I2C_PCA_ISA=m

#
# Miscellaneous I2C Chip support
#
CONFIG_SENSORS_DS1337=m
CONFIG_SENSORS_DS1374=m
CONFIG_SENSORS_EEPROM=m
CONFIG_SENSORS_PCF8574=m
CONFIG_SENSORS_PCA9539=m
CONFIG_SENSORS_PCF8591=m
CONFIG_SENSORS_MAX6875=m
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set

#
# SPI support
#
# CONFIG_SPI is not set
# CONFIG_SPI_MASTER is not set

#
# Dallas's 1-wire bus
#
CONFIG_W1=m

#
# 1-wire Bus Masters
#
CONFIG_W1_MASTER_MATROX=m
CONFIG_W1_MASTER_DS9490=m
CONFIG_W1_MASTER_DS9490_BRIDGE=m
CONFIG_W1_MASTER_DS2482=m

#
# 1-wire Slaves
#
CONFIG_W1_SLAVE_THERM=m
CONFIG_W1_SLAVE_SMEM=m
CONFIG_W1_SLAVE_DS2433=m

#
# Hardware Monitoring support
#
CONFIG_HWMON=m
CONFIG_HWMON_VID=m
CONFIG_SENSORS_ADM1021=m
CONFIG_SENSORS_ADM1025=m
CONFIG_SENSORS_ADM1026=m
CONFIG_SENSORS_ADM1031=m
CONFIG_SENSORS_ADM9240=m
CONFIG_SENSORS_ASB100=m
CONFIG_SENSORS_ATXP1=m
CONFIG_SENSORS_DS1621=m
CONFIG_SENSORS_F71805F=m
CONFIG_SENSORS_FSCHER=m
CONFIG_SENSORS_FSCPOS=m
CONFIG_SENSORS_GL518SM=m
CONFIG_SENSORS_GL520SM=m
CONFIG_SENSORS_IT87=m
CONFIG_SENSORS_LM63=m
CONFIG_SENSORS_LM75=m
CONFIG_SENSORS_LM77=m
CONFIG_SENSORS_LM78=m
CONFIG_SENSORS_LM80=m
CONFIG_SENSORS_LM83=m
CONFIG_SENSORS_LM85=m
CONFIG_SENSORS_LM87=m
CONFIG_SENSORS_LM90=m
CONFIG_SENSORS_LM92=m
CONFIG_SENSORS_MAX1619=m
CONFIG_SENSORS_PC87360=m
CONFIG_SENSORS_SIS5595=m
CONFIG_SENSORS_SMSC47M1=m
CONFIG_SENSORS_SMSC47B397=m
CONFIG_SENSORS_VIA686A=m
CONFIG_SENSORS_VT8231=m
CONFIG_SENSORS_W83781D=m
CONFIG_SENSORS_W83792D=m
CONFIG_SENSORS_W83L785TS=m
CONFIG_SENSORS_W83627HF=m
CONFIG_SENSORS_W83627EHF=m
CONFIG_SENSORS_HDAPS=m
# CONFIG_HWMON_DEBUG_CHIP is not set

#
# Misc devices
#
CONFIG_IBM_ASM=m

#
# Multimedia devices
#
CONFIG_VIDEO_DEV=m
CONFIG_VIDEO_V4L1=y
CONFIG_VIDEO_V4L1_COMPAT=y
CONFIG_VIDEO_V4L2=m

#
# Video Capture Adapters
#

#
# Video Capture Adapters
#
# CONFIG_VIDEO_ADV_DEBUG is not set
CONFIG_VIDEO_VIVI=m
CONFIG_VIDEO_BT848=m
CONFIG_VIDEO_BT848_DVB=y
CONFIG_VIDEO_SAA6588=m
CONFIG_VIDEO_PMS=m
CONFIG_VIDEO_BWQCAM=m
CONFIG_VIDEO_CQCAM=m
CONFIG_VIDEO_W9966=m
CONFIG_VIDEO_CPIA=m
CONFIG_VIDEO_CPIA_PP=m
CONFIG_VIDEO_CPIA_USB=m
CONFIG_VIDEO_CPIA2=m
CONFIG_VIDEO_SAA5246A=m
CONFIG_VIDEO_SAA5249=m
CONFIG_TUNER_3036=m
CONFIG_VIDEO_STRADIS=m
CONFIG_VIDEO_ZORAN=m
CONFIG_VIDEO_ZORAN_BUZ=m
CONFIG_VIDEO_ZORAN_DC10=m
CONFIG_VIDEO_ZORAN_DC30=m
CONFIG_VIDEO_ZORAN_LML33=m
CONFIG_VIDEO_ZORAN_LML33R10=m
CONFIG_VIDEO_MEYE=m
CONFIG_VIDEO_SAA7134=m
# CONFIG_VIDEO_SAA7134_ALSA is not set
CONFIG_VIDEO_SAA7134_DVB=m
CONFIG_VIDEO_SAA7134_DVB_ALL_FRONTENDS=y
CONFIG_VIDEO_MXB=m
CONFIG_VIDEO_DPC=m
CONFIG_VIDEO_HEXIUM_ORION=m
CONFIG_VIDEO_HEXIUM_GEMINI=m
CONFIG_VIDEO_CX88_VP3054=m
CONFIG_VIDEO_CX88=m
# CONFIG_VIDEO_CX88_ALSA is not set
CONFIG_VIDEO_CX88_DVB=m
CONFIG_VIDEO_CX88_DVB_ALL_FRONTENDS=y
CONFIG_VIDEO_OVCAMCHIP=m

#
# Encoders and Decoders
#
CONFIG_VIDEO_MSP3400=m
CONFIG_VIDEO_CS53L32A=m
CONFIG_VIDEO_WM8775=m
CONFIG_VIDEO_WM8739=m
CONFIG_VIDEO_CX25840=m
CONFIG_VIDEO_SAA711X=m
CONFIG_VIDEO_SAA7127=m
CONFIG_VIDEO_UPD64031A=m
CONFIG_VIDEO_UPD64083=m

#
# V4L USB devices
#
CONFIG_VIDEO_EM28XX=m
CONFIG_USB_DSBR=m
CONFIG_VIDEO_USBVIDEO=m
CONFIG_USB_VICAM=m
CONFIG_USB_IBMCAM=m
CONFIG_USB_KONICAWC=m
CONFIG_USB_ET61X251=m
CONFIG_USB_OV511=m
CONFIG_USB_SE401=m
CONFIG_USB_SN9C102=m
CONFIG_USB_STV680=m
CONFIG_USB_W9968CF=m
CONFIG_USB_ZC0301=m
CONFIG_USB_PWC=m

#
# Radio Adapters
#
CONFIG_RADIO_CADET=m
CONFIG_RADIO_RTRACK=m
CONFIG_RADIO_RTRACK2=m
CONFIG_RADIO_AZTECH=m
CONFIG_RADIO_GEMTEK=m
CONFIG_RADIO_GEMTEK_PCI=m
CONFIG_RADIO_MAXIRADIO=m
CONFIG_RADIO_MAESTRO=m
CONFIG_RADIO_SF16FMI=m
CONFIG_RADIO_SF16FMR2=m
CONFIG_RADIO_TERRATEC=m
CONFIG_RADIO_TRUST=m
CONFIG_RADIO_TYPHOON=m
CONFIG_RADIO_TYPHOON_PROC_FS=y
CONFIG_RADIO_ZOLTRIX=m

#
# Digital Video Broadcasting Devices
#
CONFIG_DVB=y
CONFIG_DVB_CORE=m

#
# Supported SAA7146 based PCI Adapters
#
CONFIG_DVB_AV7110=m
CONFIG_DVB_AV7110_OSD=y
CONFIG_DVB_BUDGET=m
CONFIG_DVB_BUDGET_CI=m
CONFIG_DVB_BUDGET_AV=m
CONFIG_DVB_BUDGET_PATCH=m

#
# Supported USB Adapters
#
CONFIG_DVB_USB=m
# CONFIG_DVB_USB_DEBUG is not set
CONFIG_DVB_USB_A800=m
CONFIG_DVB_USB_DIBUSB_MB=m
# CONFIG_DVB_USB_DIBUSB_MB_FAULTY is not set
CONFIG_DVB_USB_DIBUSB_MC=m
CONFIG_DVB_USB_UMT_010=m
CONFIG_DVB_USB_CXUSB=m
CONFIG_DVB_USB_DIGITV=m
CONFIG_DVB_USB_VP7045=m
CONFIG_DVB_USB_VP702X=m
CONFIG_DVB_USB_NOVA_T_USB2=m
CONFIG_DVB_USB_DTT200U=m
CONFIG_DVB_TTUSB_BUDGET=m
CONFIG_DVB_TTUSB_DEC=m
CONFIG_DVB_CINERGYT2=m
CONFIG_DVB_CINERGYT2_TUNING=y
CONFIG_DVB_CINERGYT2_STREAM_URB_COUNT=32
CONFIG_DVB_CINERGYT2_STREAM_BUF_SIZE=512
CONFIG_DVB_CINERGYT2_QUERY_INTERVAL=250
# CONFIG_DVB_CINERGYT2_ENABLE_RC_INPUT_DEVICE is not set

#
# Supported FlexCopII (B2C2) Adapters
#
CONFIG_DVB_B2C2_FLEXCOP=m
CONFIG_DVB_B2C2_FLEXCOP_PCI=m
CONFIG_DVB_B2C2_FLEXCOP_USB=m
# CONFIG_DVB_B2C2_FLEXCOP_DEBUG is not set

#
# Supported BT878 Adapters
#
CONFIG_DVB_BT8XX=m

#
# Supported Pluto2 Adapters
#
CONFIG_DVB_PLUTO2=m

#
# Supported DVB Frontends
#

#
# Customise DVB Frontends
#

#
# DVB-S (satellite) frontends
#
CONFIG_DVB_STV0299=m
CONFIG_DVB_CX24110=m
CONFIG_DVB_CX24123=m
CONFIG_DVB_TDA8083=m
CONFIG_DVB_MT312=m
CONFIG_DVB_VES1X93=m
CONFIG_DVB_S5H1420=m

#
# DVB-T (terrestrial) frontends
#
CONFIG_DVB_SP8870=m
CONFIG_DVB_SP887X=m
CONFIG_DVB_CX22700=m
CONFIG_DVB_CX22702=m
CONFIG_DVB_L64781=m
CONFIG_DVB_TDA1004X=m
CONFIG_DVB_NXT6000=m
CONFIG_DVB_MT352=m
CONFIG_DVB_ZL10353=m
CONFIG_DVB_DIB3000MB=m
CONFIG_DVB_DIB3000MC=m

#
# DVB-C (cable) frontends
#
CONFIG_DVB_VES1820=m
CONFIG_DVB_TDA10021=m
CONFIG_DVB_STV0297=m

#
# ATSC (North American/Korean Terresterial DTV) frontends
#
CONFIG_DVB_NXT200X=m
CONFIG_DVB_OR51211=m
CONFIG_DVB_OR51132=m
CONFIG_DVB_BCM3510=m
CONFIG_DVB_LGDT330X=m
CONFIG_VIDEO_SAA7146=m
CONFIG_VIDEO_SAA7146_VV=m
CONFIG_VIDEO_VIDEOBUF=m
CONFIG_VIDEO_TUNER=m
CONFIG_VIDEO_BUF=m
CONFIG_VIDEO_BUF_DVB=m
CONFIG_VIDEO_BTCX=m
CONFIG_VIDEO_IR=m
CONFIG_VIDEO_TVEEPROM=m
CONFIG_USB_DABUSB=m

#
# Graphics support
#
CONFIG_FB=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_MACMODES is not set
# CONFIG_FB_FIRMWARE_EDID is not set
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y
CONFIG_FB_CIRRUS=m
CONFIG_FB_PM2=m
# CONFIG_FB_PM2_FIFO_DISCONNECT is not set
CONFIG_FB_CYBER2000=m
CONFIG_FB_ARC=m
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
CONFIG_FB_VGA16=m
CONFIG_FB_VESA=y
CONFIG_VIDEO_SELECT=y
CONFIG_FB_HGA=m
# CONFIG_FB_HGA_ACCEL is not set
CONFIG_FB_S1D13XXX=m
CONFIG_FB_NVIDIA=m
CONFIG_FB_NVIDIA_I2C=y
CONFIG_FB_RIVA=m
CONFIG_FB_RIVA_I2C=y
# CONFIG_FB_RIVA_DEBUG is not set
CONFIG_FB_I810=m
CONFIG_FB_I810_GTF=y
CONFIG_FB_I810_I2C=y
CONFIG_FB_INTEL=m
# CONFIG_FB_INTEL_DEBUG is not set
CONFIG_FB_MATROX=m
CONFIG_FB_MATROX_MILLENIUM=y
CONFIG_FB_MATROX_MYSTIQUE=y
CONFIG_FB_MATROX_G=y
CONFIG_FB_MATROX_I2C=m
CONFIG_FB_MATROX_MAVEN=m
CONFIG_FB_MATROX_MULTIHEAD=y
CONFIG_FB_RADEON=m
CONFIG_FB_RADEON_I2C=y
# CONFIG_FB_RADEON_DEBUG is not set
CONFIG_FB_ATY128=m
CONFIG_FB_ATY=m
CONFIG_FB_ATY_CT=y
CONFIG_FB_ATY_GENERIC_LCD=y
CONFIG_FB_ATY_GX=y
CONFIG_FB_SAVAGE=m
CONFIG_FB_SAVAGE_I2C=y
CONFIG_FB_SAVAGE_ACCEL=y
CONFIG_FB_SIS=m
CONFIG_FB_SIS_300=y
CONFIG_FB_SIS_315=y
CONFIG_FB_NEOMAGIC=m
CONFIG_FB_KYRO=m
CONFIG_FB_3DFX=m
# CONFIG_FB_3DFX_ACCEL is not set
CONFIG_FB_VOODOO1=m
CONFIG_FB_CYBLA=m
CONFIG_FB_TRIDENT=m
# CONFIG_FB_TRIDENT_ACCEL is not set
CONFIG_FB_GEODE=y
CONFIG_FB_GEODE_GX=m
CONFIG_FB_GEODE_GX1=m
# CONFIG_FB_VIRTUAL is not set

#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
CONFIG_VGACON_SOFT_SCROLLBACK=y
CONFIG_VGACON_SOFT_SCROLLBACK_SIZE=64
CONFIG_MDA_CONSOLE=m
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
CONFIG_FONTS=y
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
# CONFIG_FONT_6x11 is not set
# CONFIG_FONT_7x14 is not set
# CONFIG_FONT_PEARL_8x8 is not set
# CONFIG_FONT_ACORN_8x8 is not set
# CONFIG_FONT_MINI_4x6 is not set
# CONFIG_FONT_SUN8x16 is not set
# CONFIG_FONT_SUN12x22 is not set
# CONFIG_FONT_10x18 is not set

#
# Logo configuration
#
CONFIG_LOGO=y
# CONFIG_LOGO_LINUX_MONO is not set
# CONFIG_LOGO_LINUX_VGA16 is not set
CONFIG_LOGO_LINUX_CLUT224=y
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_BACKLIGHT_CLASS_DEVICE=m
CONFIG_BACKLIGHT_DEVICE=y
CONFIG_LCD_CLASS_DEVICE=m
CONFIG_LCD_DEVICE=y

#
# Sound
#
CONFIG_SOUND=m

#
# Advanced Linux Sound Architecture
#
CONFIG_SND=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
CONFIG_SND_HWDEP=m
CONFIG_SND_RAWMIDI=m
CONFIG_SND_SEQUENCER=m
CONFIG_SND_SEQ_DUMMY=m
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
CONFIG_SND_PCM_OSS_PLUGINS=y
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_RTCTIMER=m
CONFIG_SND_SEQ_RTCTIMER_DEFAULT=y
# CONFIG_SND_DYNAMIC_MINORS is not set
CONFIG_SND_SUPPORT_OLD_API=y
CONFIG_SND_VERBOSE_PROCFS=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set

#
# Generic devices
#
CONFIG_SND_MPU401_UART=m
CONFIG_SND_OPL3_LIB=m
CONFIG_SND_OPL4_LIB=m
CONFIG_SND_VX_LIB=m
CONFIG_SND_AC97_CODEC=m
CONFIG_SND_AC97_BUS=m
CONFIG_SND_DUMMY=m
CONFIG_SND_VIRMIDI=m
CONFIG_SND_MTPAV=m
CONFIG_SND_SERIAL_U16550=m
CONFIG_SND_MPU401=m

#
# ISA devices
#
CONFIG_SND_AD1848_LIB=m
CONFIG_SND_CS4231_LIB=m
CONFIG_SND_ADLIB=m
CONFIG_SND_AD1816A=m
CONFIG_SND_AD1848=m
CONFIG_SND_ALS100=m
CONFIG_SND_AZT2320=m
CONFIG_SND_CMI8330=m
CONFIG_SND_CS4231=m
CONFIG_SND_CS4232=m
CONFIG_SND_CS4236=m
CONFIG_SND_DT019X=m
CONFIG_SND_ES968=m
CONFIG_SND_ES1688=m
CONFIG_SND_ES18XX=m
CONFIG_SND_GUS_SYNTH=m
CONFIG_SND_GUSCLASSIC=m
CONFIG_SND_GUSEXTREME=m
CONFIG_SND_GUSMAX=m
CONFIG_SND_INTERWAVE=m
CONFIG_SND_INTERWAVE_STB=m
CONFIG_SND_OPL3SA2=m
CONFIG_SND_OPTI92X_AD1848=m
CONFIG_SND_OPTI92X_CS4231=m
CONFIG_SND_OPTI93X=m
CONFIG_SND_MIRO=m
CONFIG_SND_SB8=m
CONFIG_SND_SB16=m
CONFIG_SND_SBAWE=m
CONFIG_SND_SB16_CSP=y
CONFIG_SND_SGALAXY=m
CONFIG_SND_SSCAPE=m
CONFIG_SND_WAVEFRONT=m

#
# PCI devices
#
CONFIG_SND_AD1889=m
CONFIG_SND_ALS300=m
CONFIG_SND_ALS4000=m
CONFIG_SND_ALI5451=m
CONFIG_SND_ATIIXP=m
CONFIG_SND_ATIIXP_MODEM=m
CONFIG_SND_AU8810=m
CONFIG_SND_AU8820=m
CONFIG_SND_AU8830=m
CONFIG_SND_AZT3328=m
CONFIG_SND_BT87X=m
# CONFIG_SND_BT87X_OVERCLOCK is not set
CONFIG_SND_CA0106=m
CONFIG_SND_CMIPCI=m
CONFIG_SND_CS4281=m
CONFIG_SND_CS46XX=m
CONFIG_SND_CS46XX_NEW_DSP=y
CONFIG_SND_CS5535AUDIO=m
CONFIG_SND_EMU10K1=m
CONFIG_SND_EMU10K1X=m
CONFIG_SND_ENS1370=m
CONFIG_SND_ENS1371=m
CONFIG_SND_ES1938=m
CONFIG_SND_ES1968=m
CONFIG_SND_FM801=m
CONFIG_SND_FM801_TEA575X=m
CONFIG_SND_HDA_INTEL=m
CONFIG_SND_HDSP=m
CONFIG_SND_HDSPM=m
CONFIG_SND_ICE1712=m
CONFIG_SND_ICE1724=m
CONFIG_SND_INTEL8X0=m
CONFIG_SND_INTEL8X0M=m
CONFIG_SND_KORG1212=m
CONFIG_SND_MAESTRO3=m
CONFIG_SND_MIXART=m
CONFIG_SND_NM256=m
CONFIG_SND_PCXHR=m
CONFIG_SND_RIPTIDE=m
CONFIG_SND_RME32=m
CONFIG_SND_RME96=m
CONFIG_SND_RME9652=m
CONFIG_SND_SONICVIBES=m
CONFIG_SND_TRIDENT=m
CONFIG_SND_VIA82XX=m
CONFIG_SND_VIA82XX_MODEM=m
CONFIG_SND_VX222=m
CONFIG_SND_YMFPCI=m

#
# USB devices
#
CONFIG_SND_USB_AUDIO=m
CONFIG_SND_USB_USX2Y=m

#
# PCMCIA devices
#
CONFIG_SND_VXPOCKET=m
CONFIG_SND_PDAUDIOCF=m

#
# Open Sound System
#
# CONFIG_SOUND_PRIME is not set

#
# USB support
#
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set

#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_SUSPEND is not set
# CONFIG_USB_OTG is not set

#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=m
CONFIG_USB_EHCI_SPLIT_ISO=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
CONFIG_USB_ISP116X_HCD=m
CONFIG_USB_OHCI_HCD=m
# CONFIG_USB_OHCI_BIG_ENDIAN is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_UHCI_HCD=m
CONFIG_USB_SL811_HCD=m
CONFIG_USB_SL811_CS=m

#
# USB Device Class drivers
#
CONFIG_USB_ACM=m
CONFIG_USB_PRINTER=m

#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#

#
# may also be needed; see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
CONFIG_USB_STORAGE_DATAFAB=y
CONFIG_USB_STORAGE_FREECOM=y
CONFIG_USB_STORAGE_ISD200=y
CONFIG_USB_STORAGE_DPCM=y
CONFIG_USB_STORAGE_USBAT=y
CONFIG_USB_STORAGE_SDDR09=y
CONFIG_USB_STORAGE_SDDR55=y
CONFIG_USB_STORAGE_JUMPSHOT=y
CONFIG_USB_STORAGE_ALAUDA=y
# CONFIG_USB_LIBUSUAL is not set

#
# USB Input Devices
#
CONFIG_USB_HID=y
CONFIG_USB_HIDINPUT=y
# CONFIG_USB_HIDINPUT_POWERBOOK is not set
CONFIG_HID_FF=y
CONFIG_HID_PID=y
CONFIG_LOGITECH_FF=y
CONFIG_THRUSTMASTER_FF=y
CONFIG_USB_HIDDEV=y
CONFIG_USB_AIPTEK=m
CONFIG_USB_WACOM=m
CONFIG_USB_ACECAD=m
CONFIG_USB_KBTAB=m
CONFIG_USB_POWERMATE=m
CONFIG_USB_TOUCHSCREEN=m
CONFIG_USB_TOUCHSCREEN_EGALAX=y
CONFIG_USB_TOUCHSCREEN_PANJIT=y
CONFIG_USB_TOUCHSCREEN_3M=y
CONFIG_USB_TOUCHSCREEN_ITM=y
CONFIG_USB_YEALINK=m
CONFIG_USB_XPAD=m
CONFIG_USB_ATI_REMOTE=m
CONFIG_USB_ATI_REMOTE2=m
CONFIG_USB_KEYSPAN_REMOTE=m
CONFIG_USB_APPLETOUCH=m

#
# USB Imaging devices
#
CONFIG_USB_MDC800=m
CONFIG_USB_MICROTEK=m

#
# USB Network Adapters
#
CONFIG_USB_CATC=m
CONFIG_USB_KAWETH=m
CONFIG_USB_PEGASUS=m
CONFIG_USB_RTL8150=m
CONFIG_USB_USBNET=m
CONFIG_USB_NET_AX8817X=m
CONFIG_USB_NET_CDCETHER=m
CONFIG_USB_NET_GL620A=m
CONFIG_USB_NET_NET1080=m
CONFIG_USB_NET_PLUSB=m
CONFIG_USB_NET_RNDIS_HOST=m
CONFIG_USB_NET_CDC_SUBSET=m
CONFIG_USB_ALI_M5632=y
CONFIG_USB_AN2720=y
CONFIG_USB_BELKIN=y
CONFIG_USB_ARMLINUX=y
# CONFIG_USB_EPSON2888 is not set
CONFIG_USB_NET_ZAURUS=m
CONFIG_USB_ZD1201=m
CONFIG_USB_MON=y

#
# USB port drivers
#
CONFIG_USB_USS720=m

#
# USB Serial Converter support
#
CONFIG_USB_SERIAL=m
CONFIG_USB_SERIAL_GENERIC=y
CONFIG_USB_SERIAL_AIRPRIME=m
CONFIG_USB_SERIAL_ANYDATA=m
CONFIG_USB_SERIAL_ARK3116=m
CONFIG_USB_SERIAL_BELKIN=m
CONFIG_USB_SERIAL_WHITEHEAT=m
CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
CONFIG_USB_SERIAL_CP2101=m
CONFIG_USB_SERIAL_CYPRESS_M8=m
CONFIG_USB_SERIAL_EMPEG=m
CONFIG_USB_SERIAL_FTDI_SIO=m
CONFIG_USB_SERIAL_FUNSOFT=m
CONFIG_USB_SERIAL_VISOR=m
CONFIG_USB_SERIAL_IPAQ=m
CONFIG_USB_SERIAL_IR=m
CONFIG_USB_SERIAL_EDGEPORT=m
CONFIG_USB_SERIAL_EDGEPORT_TI=m
CONFIG_USB_SERIAL_GARMIN=m
CONFIG_USB_SERIAL_IPW=m
CONFIG_USB_SERIAL_KEYSPAN_PDA=m
CONFIG_USB_SERIAL_KEYSPAN=m
CONFIG_USB_SERIAL_KEYSPAN_MPR=y
CONFIG_USB_SERIAL_KEYSPAN_USA28=y
CONFIG_USB_SERIAL_KEYSPAN_USA28X=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XA=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XB=y
CONFIG_USB_SERIAL_KEYSPAN_USA19=y
CONFIG_USB_SERIAL_KEYSPAN_USA18X=y
CONFIG_USB_SERIAL_KEYSPAN_USA19W=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QW=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QI=y
CONFIG_USB_SERIAL_KEYSPAN_USA49W=y
CONFIG_USB_SERIAL_KEYSPAN_USA49WLC=y
CONFIG_USB_SERIAL_KLSI=m
CONFIG_USB_SERIAL_KOBIL_SCT=m
CONFIG_USB_SERIAL_MCT_U232=m
CONFIG_USB_SERIAL_NAVMAN=m
CONFIG_USB_SERIAL_PL2303=m
CONFIG_USB_SERIAL_HP4X=m
CONFIG_USB_SERIAL_SAFE=m
CONFIG_USB_SERIAL_SAFE_PADDED=y
CONFIG_USB_SERIAL_TI=m
CONFIG_USB_SERIAL_CYBERJACK=m
CONFIG_USB_SERIAL_XIRCOM=m
CONFIG_USB_SERIAL_OPTION=m
CONFIG_USB_SERIAL_OMNINET=m
CONFIG_USB_EZUSB=y

#
# USB Miscellaneous drivers
#
CONFIG_USB_EMI62=m
CONFIG_USB_EMI26=m
CONFIG_USB_AUERSWALD=m
CONFIG_USB_RIO500=m
CONFIG_USB_LEGOTOWER=m
CONFIG_USB_LCD=m
CONFIG_USB_LED=m
CONFIG_USB_CYTHERM=m
CONFIG_USB_PHIDGETKIT=m
CONFIG_USB_PHIDGETSERVO=m
CONFIG_USB_IDMOUSE=m
CONFIG_USB_SISUSBVGA=m
CONFIG_USB_SISUSBVGA_CON=y
CONFIG_USB_LD=m
CONFIG_USB_TEST=m

#
# USB DSL modem support
#
CONFIG_USB_ATM=m
CONFIG_USB_SPEEDTOUCH=m
CONFIG_USB_CXACRU=m
CONFIG_USB_UEAGLEATM=m
CONFIG_USB_XUSBATM=m

#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set

#
# MMC/SD Card support
#
CONFIG_MMC=m
# CONFIG_MMC_DEBUG is not set
CONFIG_MMC_BLOCK=m
CONFIG_MMC_SDHCI=m
CONFIG_MMC_WBSD=m

#
# LED devices
#
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=m

#
# LED drivers
#

#
# LED Triggers
#
CONFIG_LEDS_TRIGGERS=y
CONFIG_LEDS_TRIGGER_TIMER=m
CONFIG_LEDS_TRIGGER_IDE_DISK=y

#
# InfiniBand support
#
CONFIG_INFINIBAND=m
CONFIG_INFINIBAND_USER_MAD=m
CONFIG_INFINIBAND_USER_ACCESS=m
CONFIG_INFINIBAND_MTHCA=m
CONFIG_INFINIBAND_MTHCA_DEBUG=y
CONFIG_INFINIBAND_IPOIB=m
CONFIG_INFINIBAND_IPOIB_DEBUG=y
# CONFIG_INFINIBAND_IPOIB_DEBUG_DATA is not set
CONFIG_INFINIBAND_SRP=m

#
# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
#
# CONFIG_EDAC is not set

#
# Real Time Clock
#
CONFIG_RTC_LIB=m
CONFIG_RTC_CLASS=m

#
# RTC interfaces
#
CONFIG_RTC_INTF_SYSFS=m
CONFIG_RTC_INTF_PROC=m
CONFIG_RTC_INTF_DEV=m

#
# RTC drivers
#
CONFIG_RTC_DRV_X1205=m
CONFIG_RTC_DRV_DS1672=m
CONFIG_RTC_DRV_PCF8563=m
CONFIG_RTC_DRV_RS5C372=m
CONFIG_RTC_DRV_M48T86=m
CONFIG_RTC_DRV_TEST=m

#
# File systems
#
CONFIG_EXT2_FS=y
# CONFIG_EXT2_FS_XATTR is not set
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=m
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
CONFIG_JBD=m
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
CONFIG_REISERFS_FS=m
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
CONFIG_REISERFS_FS_XATTR=y
CONFIG_REISERFS_FS_POSIX_ACL=y
CONFIG_REISERFS_FS_SECURITY=y
CONFIG_JFS_FS=m
CONFIG_JFS_POSIX_ACL=y
CONFIG_JFS_SECURITY=y
# CONFIG_JFS_DEBUG is not set
# CONFIG_JFS_STATISTICS is not set
CONFIG_FS_POSIX_ACL=y
CONFIG_XFS_FS=m
CONFIG_XFS_EXPORT=y
CONFIG_XFS_QUOTA=y
CONFIG_XFS_SECURITY=y
CONFIG_XFS_POSIX_ACL=y
# CONFIG_XFS_RT is not set
CONFIG_OCFS2_FS=m
CONFIG_MINIX_FS=m
CONFIG_ROMFS_FS=m
CONFIG_INOTIFY=y
CONFIG_QUOTA=y
CONFIG_QFMT_V1=m
CONFIG_QFMT_V2=m
CONFIG_QUOTACTL=y
CONFIG_DNOTIFY=y
CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=m
CONFIG_FUSE_FS=m

#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=m
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_ZISOFS_FS=m
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y

#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
CONFIG_NTFS_FS=m
# CONFIG_NTFS_DEBUG is not set
CONFIG_NTFS_RW=y

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
CONFIG_CONFIGFS_FS=m

#
# Miscellaneous filesystems
#
CONFIG_ADFS_FS=m
# CONFIG_ADFS_FS_RW is not set
CONFIG_AFFS_FS=m
CONFIG_HFS_FS=m
CONFIG_HFSPLUS_FS=m
CONFIG_BEFS_FS=m
# CONFIG_BEFS_DEBUG is not set
CONFIG_BFS_FS=m
CONFIG_EFS_FS=m
CONFIG_CRAMFS=m
CONFIG_VXFS_FS=m
CONFIG_HPFS_FS=m
CONFIG_QNX4FS_FS=m
CONFIG_SYSV_FS=m
CONFIG_UFS_FS=m

#
# Network File Systems
#
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
CONFIG_NFS_DIRECTIO=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
CONFIG_NFSD_V4=y
CONFIG_NFSD_TCP=y
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
CONFIG_SUNRPC_GSS=m
CONFIG_RPCSEC_GSS_KRB5=m
CONFIG_RPCSEC_GSS_SPKM3=m
CONFIG_SMB_FS=m
# CONFIG_SMB_NLS_DEFAULT is not set
CONFIG_CIFS=m
# CONFIG_CIFS_STATS is not set
# CONFIG_CIFS_XATTR is not set
# CONFIG_CIFS_EXPERIMENTAL is not set
CONFIG_NCP_FS=m
CONFIG_NCPFS_PACKET_SIGNING=y
CONFIG_NCPFS_IOCTL_LOCKING=y
CONFIG_NCPFS_STRONG=y
CONFIG_NCPFS_NFS_NS=y
CONFIG_NCPFS_OS2_NS=y
CONFIG_NCPFS_SMALLDOS=y
CONFIG_NCPFS_NLS=y
CONFIG_NCPFS_EXTRAS=y
CONFIG_CODA_FS=m
# CONFIG_CODA_FS_OLD_API is not set
CONFIG_AFS_FS=m
CONFIG_RXRPC=m
# CONFIG_9P_FS is not set

#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
# CONFIG_OSF_PARTITION is not set
# CONFIG_AMIGA_PARTITION is not set
# CONFIG_ATARI_PARTITION is not set
CONFIG_MAC_PARTITION=y
CONFIG_MSDOS_PARTITION=y
CONFIG_BSD_DISKLABEL=y
# CONFIG_MINIX_SUBPARTITION is not set
CONFIG_SOLARIS_X86_PARTITION=y
# CONFIG_UNIXWARE_DISKLABEL is not set
# CONFIG_LDM_PARTITION is not set
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
CONFIG_KARMA_PARTITION=y
# CONFIG_EFI_PARTITION is not set

#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="utf8"
CONFIG_NLS_CODEPAGE_437=m
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_CODEPAGE_775=m
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_CODEPAGE_852=m
CONFIG_NLS_CODEPAGE_855=m
CONFIG_NLS_CODEPAGE_857=m
CONFIG_NLS_CODEPAGE_860=m
CONFIG_NLS_CODEPAGE_861=m
CONFIG_NLS_CODEPAGE_862=m
CONFIG_NLS_CODEPAGE_863=m
CONFIG_NLS_CODEPAGE_864=m
CONFIG_NLS_CODEPAGE_865=m
CONFIG_NLS_CODEPAGE_866=m
CONFIG_NLS_CODEPAGE_869=m
CONFIG_NLS_CODEPAGE_936=m
CONFIG_NLS_CODEPAGE_950=m
CONFIG_NLS_CODEPAGE_932=m
CONFIG_NLS_CODEPAGE_949=m
CONFIG_NLS_CODEPAGE_874=m
CONFIG_NLS_ISO8859_8=m
CONFIG_NLS_CODEPAGE_1250=m
CONFIG_NLS_CODEPAGE_1251=m
CONFIG_NLS_ASCII=m
CONFIG_NLS_ISO8859_1=m
CONFIG_NLS_ISO8859_2=m
CONFIG_NLS_ISO8859_3=m
CONFIG_NLS_ISO8859_4=m
CONFIG_NLS_ISO8859_5=m
CONFIG_NLS_ISO8859_6=m
CONFIG_NLS_ISO8859_7=m
CONFIG_NLS_ISO8859_9=m
CONFIG_NLS_ISO8859_13=m
CONFIG_NLS_ISO8859_14=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
CONFIG_NLS_UTF8=m

#
# Instrumentation Support
#
# CONFIG_PROFILING is not set
# CONFIG_KPROBES is not set

#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_DEBUG_KERNEL is not set
CONFIG_LOG_BUF_SHIFT=14
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_FS is not set
# CONFIG_UNWIND_INFO is not set
CONFIG_EARLY_PRINTK=y
CONFIG_STACK_BACKTRACE_COLS=2
CONFIG_DOUBLEFAULT=y

#
# Security options
#
# CONFIG_KEYS is not set
CONFIG_SECURITY=y
CONFIG_SECURITY_NETWORK=y
# CONFIG_SECURITY_NETWORK_XFRM is not set
CONFIG_SECURITY_CAPABIL

n3tfr33 · Messaggio da **n3tfr33** » mar 18 lug 2006, 4:48

prosegue config

CONFIG_SECURITY_ROOTPLUG=m
CONFIG_SECURITY_SECLVL=m

#
# Cryptographic options
#
CONFIG_CRYPTO=y
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_WP512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_DES=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_SERPENT=m
CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_AES_586=m
CONFIG_CRYPTO_CAST5=m
CONFIG_CRYPTO_CAST6=m
CONFIG_CRYPTO_TEA=m
CONFIG_CRYPTO_ARC4=m
CONFIG_CRYPTO_KHAZAD=m
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_DEFLATE=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_CRC32C=m
CONFIG_CRYPTO_TEST=m

#
# Hardware crypto devices
#
CONFIG_CRYPTO_DEV_PADLOCK=m
CONFIG_CRYPTO_DEV_PADLOCK_AES=y

#
# Library routines
#
CONFIG_CRC_CCITT=m
CONFIG_CRC16=m
CONFIG_CRC32=y
CONFIG_LIBCRC32C=m
CONFIG_ZLIB_INFLATE=m
CONFIG_ZLIB_DEFLATE=m
CONFIG_TEXTSEARCH=y
CONFIG_TEXTSEARCH_KMP=m
CONFIG_TEXTSEARCH_BM=m
CONFIG_TEXTSEARCH_FSM=m
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_X86_BIOS_REBOOT=y
CONFIG_KTIME_SCALAR=y

/sbin/lspci

00:00.0 Host bridge: VIA Technologies, Inc. P/KN266 Host Bridge
00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP]
00:09.0 CardBus bridge: ENE Technology Inc CB-710/2/4 Cardbus Controller (rev 01)
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
00:11.6 Communication controller: VIA Technologies, Inc. AC'97 Modem Controller (rev 80)
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)
01:00.0 VGA compatible controller: S3 Inc. VT8375 [ProSavage8 KM266/KL266]

Messaggio da **phobos3576** » mar 18 lug 2006, 15:12

Il .config va bene per la parte relativa alla scheda video; l'AGP Bridge è basato su chipset VIA.

NON devi lanciare /etc/rc.d/rc.modules; si tratta infatti di uno script che viene eseguito automaticamente all'avvio di Linux!
Lo devi aprire con un editor di testo (ad esempio, KWrite) per verificare se ci sono delle righe del tipo:

modprobe agpgart

Eventualmente, commenta tali righe e verifica che sia il kernel a caricare tutti i moduli AGP in automatico.

n3tfr33 · Messaggio da **n3tfr33** » mer 19 lug 2006, 1:54

Non ho trovato le righe che mi hai detto...te lo posto tutto.
#!/bin/sh
# rc.modules 3.1 Thu Aug 28 14:01:35 PDT 2003 pjv <volkerdi@slackware.com>
#
# This file loads extra drivers into the Linux kernel.
# The modules will be looked for under /lib/modules/<kernel version number>
# On systems using KMOD this file will be mostly commented out, but is still
# useful for loading selected modules at boot time.
#
# Most Linux kernel modules will accept extra options such as IRQ or base
# address, or to set various modes (such as 10baseT or BNC, etc). The Linux
# kernel source is the best place to look for extra documentation for the
# various modules. This can be found under /usr/src/linux/Documentation if
# you've the installed the kernel sources. Also, the kernel source docs are
# present on the Slackware CD in the /docs/linux-2.x.x directory.
#
# NOTE: This may not be a complete list of modules. If you don't see what
# you're looking for, look around in /lib/modules/2.x.x/ for an appropriate
# module. Also, if any problems arise loading or using these modules, try
# compiling and installing a custom kernel that contains the support instead.
# That always works. ;^)
#

### Update module dependencies ###
RELEASE=`uname -r`
# If /usr is mounted and we have 'find', we can try to take a shortcut:
if [ -x /usr/bin/find -a -e /lib/modules/$RELEASE/modules.dep \
-a /lib/modules/$RELEASE/modules.dep -nt /etc/modules.conf ]; then
NEWMODS="`/usr/bin/find /lib/modules/$RELEASE -type f -newer /lib/modules/$RELEASE/modules.dep`"
# Only rebuild dependencies if new module(s) are found:
if [ ! "" = "$NEWMODS" ]; then
echo "Updating module dependencies for Linux $RELEASE:"
/sbin/depmod -a
else
echo "Module dependencies up to date (no new kernel modules found)."
fi
else # we don't have find, or there is no existing modules.dep, or it is out of date.
echo "Updating module dependencies for Linux $RELEASE:"
/sbin/depmod -A
fi

### Mouse support:
# PS/2 mouse support:
modprobe psmouse proto=imps
# This is a rare type of busmouse that is connected to the back of an
# ATI video card:
#/sbin/modprobe atixlmouse
# Logitech mouse connected to a proprietary interface card. It's
# generally a round connector with 9 pins. Note that the newer mice
# made by Logitech don't use the Logitech protocol anymore; for those,
# you don't need this option:
#/sbin/modprobe busmouse
# Microsoft busmouse support. These animals (also called Inport mice) are
# connected to an expansion board using a round connector with 9 pins. Be
# aware that several vendors talk about 'Microsoft busmouse' and actually
# mean PS/2 busmouse -- so count the pins on the connector:
#/sbin/modprobe msbusmouse
# C&T 82C710 mouse port support (as on TI Travelmate):
#/sbin/modprobe qpmouse
# IBM PC110 palmtop digitizer pad:
#/sbin/modprobe pc110pad

#### APM support ###
# APM is a BIOS specification for saving power using several different
# techniques. This is mostly useful for battery powered laptops.
#/sbin/modprobe apm

#### PC parallel port support ###
#if cat /proc/ksyms | grep "\[parport_pc\]" 1> /dev/null 2> /dev/null ; then
# echo "parport0 is built-in, not loading module" > /dev/null
#else
# if [ -r /lib/modules/$RELEASE/kernel/drivers/parport/parport_pc.o \
# -o -r /lib/modules/$RELEASE/kernel/drivers/parport/parport_pc.o.gz \
# -o -r /lib/modules/$RELEASE/kernel/drivers/parport/parport_pc.ko ]; then
# # Generic setup example:
# /sbin/modprobe parport_pc
# # Hardware specific setup example (required for PLIP and better
# # performance in general):
# #/sbin/modprobe parport_pc io=0x378 irq=7
# fi
#fi

#### Parallel printer support ###
#if cat /proc/ksyms | grep "\[lp\]" 1> /dev/null 2> /dev/null ; then
# echo "lp support built-in, not loading module" > /dev/null
#else
# if [ -r /lib/modules/$RELEASE/kernel/drivers/char/lp.o \
# -o -r /lib/modules/$RELEASE/kernel/drivers/char/lp.o.gz \
# -o -r /lib/modules/$RELEASE/kernel/drivers/char/lp.ko ]; then
# /sbin/modprobe lp
# fi
#fi

### Parallel port IP ###
#/sbin/modprobe plip

### Filesystem Quota support ###
if grep -q quota /etc/fstab ; then
# modprobe quota_v1
modprobe quota_v2
fi

### AGP (Accelerated Graphics Port) GART support ###
# This module takes care of programming the GART (part of your motherboard's
# chipset that handles gathering data from memory and passing it to the
# card) and enables faster AGP transfers. The AGP GART module is required
# to use AGP features of your 3D rendering video card. You'll need this to
# use XFree86's direct rendering support, for example.
if ! grep noagp /proc/cmdline; then
echo "[0;1mUse 'slax noagp' boot parameter to skip the following step:[0;0m"
/sbin/modprobe agpgart
fi

### non-IDE CD-ROM drive support ###
# These modules add CD-ROM drive support. Most of these drivers will probe
# for the I/O address and IRQ of the drive automatically if the parameters
# to configure them are omitted. Typically the I/O address will be specified
# in hexadecimal, e.g.: cm206=0x300,11
#
# ***NONE*** of these drivers are for use with IDE/ATAPI CD-ROM drives. That
# support is already built into every pre-compiled Slackware Linux kernel.
# Also, note that all of the manufacturers listed below stopped making these
# types of wacky-interface drives years ago and all make IDE/ATAPI-interface
# CD-ROM drives now. So, just because your drive says "Mitsumi" on it is not
# reason enough to think you need the special Mitsumi module loaded, etc. If
# you got your drive within the last couple of years it's probably IDE. Try
# tossing a disc in the drive and mounting it on the various IDE interfaces it
# could be using, like /dev/hdc.
#
#/sbin/modprobe aztcd aztcd=<I/O address>
#/sbin/modprobe cdu31a cdu31a_port=<I/O address> cdu31a_irq=<interrupt>
#/sbin/modprobe cm206 cm206=<I/O address>,<IRQ>
#/sbin/modprobe gscd gscd=<I/O address>
#/sbin/modprobe mcd mcd=<I/O address>,<IRQ>
#/sbin/modprobe mcdx mcdx=<I/O address>,<IRQ>
#/sbin/modprobe optcd optcd=<I/O address>
# Below, this last number is "1" for SoundBlaster Pro card, or "0" for a clone.
#/sbin/modprobe sbpcd sbpcd=<I/O address>,1
#/sbin/modprobe sonycd535 sonycd535=<I/O address>
#/sbin/modprobe sjcd sjcd=<I/O address>

# CD-ROM drives on ISP16, MAD16 or Mozart sound card:
#/sbin/modprobe isp16=[<port>[,<irq>[,<dma>]]][[,]<drive_type>]
# where the values are one of: port=0x340,0x320,0x330,0x360
# irq=0,3,5,7,9,10,11
# dma=0,3,5,6,7
# drive_type=noisp16,Sanyo,Panasonic,Sony,Mitsumi

### Cyclades multiport serial card support ###
#/sbin/modprobe cyclades

#### Serial line IP support (SLIP/CSLIP/PPP) ###
## This module is for SLIP/CSLIP support:
#/sbin/modprobe slip

## Load PPP:
## Check kernel version to determine module names to use
#if [ "`uname -r | cut -f 1,2 -d .`" = "2.2" ]; then
# # This module is for PPP support:
# /sbin/modprobe ppp
#else # assume 2.4 or newer
# # This module is for PPP support:
# /sbin/modprobe ppp_generic
# # This PPP plugin supports PPP over serial lines:
# /sbin/modprobe ppp_async
# # Use this plugin instead for HDLC (used for high-speed leased lines like T1/E1)
# # /sbin/modprobe ppp_synctty
#fi
## This module provides compression for PPP (optional):
##/sbin/modprobe ppp_deflate

### USB Host Controllers:
# Universal Host Controller Interface (Intel standard):
#/sbin/modprobe usb-uhci
# Universal Host Controller Interface (alternate JE):
#/sbin/modprobe uhci
# Open Host Controller Interface (Compaq/Microsoft/National standard):
#/sbin/modprobe usb-ohci

### USB device support:
# (Note that once you've loaded USB hub support most USB devices will
# trigger the kernel to load their modules automatically)
# USB "Human Interface Device" driver; handles most USB mice, joysticks,
# gamepads, steering wheels, keyboards, trackballs and digitizers.
#/sbin/modprobe hid
# Simple HIDBP USB mouse driver, if hid doesn't work:
#/sbin/modprobe usbmouse
# Simple HIDBP USB keyboard driver, if hid doesn't work:
#/sbin/modprobe usbkbd
# Wacom Graphire and Intuos tablet driver:
#/sbin/modprobe wacom
# Logitech WingMan Force joystick:
#/sbin/modprobe wmforce
# USB audio:
#/sbin/modprobe audio
# USB modem support:
#/sbin/modprobe acm
# USB serial converter:
#/sbin/modprobe usbserial
# USB printer support:
#/sbin/modprobe printer
# IBM "C-It" USB video camera:
#/sbin/modprobe ibmcam framerate=1
# USB OV511 Camera support:
#/sbin/modprobe ov511
# USB ADMtek Pegasus-based ethernet device support:
#/sbin/modprobe pegasus
# Kawasaki USB ethernet controller support:
#/sbin/modprobe kaweth
# USB Kodak DC-2xx Camera support:
#/sbin/modprobe dc2xx
# USB Mustek MDC800 Digital Camera Support:
#/sbin/modprobe mdc800
# USB Mass Storage support:
#/sbin/modprobe usb-storage
# USS720 parallel-port driver:
#/sbin/modprobe uss720
# Prolific PL-2302 USB-to-USB network device:
#/sbin/modprobe plusb
# USB Diamond Rio500 support:
#/sbin/modprobe rio500
# D-Link DSB-R100 FM radio support:
#/sbin/modprobe dsbr100
# USB Bluetooth support:
#/sbin/modprobe bluetooth
# USB scanner support (requires patched SANE from http://fachschaft.cup.uni-muenchen.de/~ ... anner.html):
#/sbin/modprobe scanner

### USB event drivers:
# Keyboard input:
#/sbin/modprobe keybdev
# Mouse input:
#/sbin/modprobe mousedev
# Joystick input:
#/sbin/modprobe joydev
# Generic event reporting device:
#/sbin/modprobe evdev

### OSS Sound support ###
### (Old Sound System

# Sound Blaster Pro/16 support:
#/sbin/modprobe sb io=0x220 irq=5 dma=3 dma16=5 mpu_io=0x300
# Sound Blaster Live support:
#/sbin/modprobe emu10k1
# MAD16 support:
#/sbin/modprobe mad16 io=0x530 irq=7 dma=0 dma16=1
# AD1816(A) sound driver:
#/sbin/modprobe modprobe ad1816 io=0x530 irq=5 dma=1 dma2=3 ad1816_clockfreq=33000
# Crystal CS4232 based (PnP) cards:
#/sbin/modprobe cs4232
# ES1370 support, such as Sound Blaster 128PCI:
#/sbin/modprobe es1370
# ES1371 support, such as Sound Blaster 64V PCI:
#/sbin/modprobe es1371
# ESS Maestro, Maestro2, Maestro2E:
#/sbin/modprobe maestro
# ESS Maestro3/Allegro:
#/sbin/modprobe maestro3
# VIA VT82Cxxx Audio Controller
#/sbin/modprobe via82cxxx_audio
# (For information on configuring other sound cards with Linux,
# see the documentation in /usr/src/linux/Documentation/sound/,
# and /usr/src/linux/Documentation/Configure.help.

### Joystick support ###
# The core joystick input support module, needed by all of the
# joystick devices below:
#/sbin/modprobe joydev
### Next, you must load a module for your gameport.
# Classic ISA/PnP gameports:
#/sbin/modprobe ns558
# Crystal SoundFusion gameports:
#/sbin/modprobe cs461x
# Aureal Vortex and Trident 4DWave gameports:
#/sbin/modprobe pcigame
# SoundBlaster Live! gameports:
#/sbin/modprobe emu10k1-gp
### Drivers for various joystick devices ###
# Analog joysticks and gamepads:
#/sbin/modprobe analog
# Assassin 3D and MadCatz Panther devices:
#/sbin/modprobe a3d
# Logitech ADI digital joysticks and gamepads:
#/sbin/modprobe adi
# Creative Labs Blaster Cobra gamepad:
#/sbin/modprobe cobra
# Genius Flight2000 Digital joysticks and gamepads:
#/sbin/modprobe gf2k
# Gravis GrIP joysticks and gamepads:
#/sbin/modprobe grip
# InterAct digital joysticks and gamepads:
#/sbin/modprobe interact
# ThrustMaster DirectConnect joysticks and gamepads:
#/sbin/modprobe tmdc
# Microsoft SideWinder digital joysticks and gamepads:
#/sbin/modprobe sidewinder
### Serial port game controller support ###
# Both of these are needed for serial-port game controllers:
#/sbin/modprobe serio
#/sbin/modprobe serport
# Logitech WingMan Warrior joystick:
#/sbin/modprobe warrior
# LogiCad3d Magellan/SpaceMouse 6dof controller:
#/sbin/modprobe magellan
# SpaceTec SpaceOrb/Avenger 6dof controller:
#/sbin/modprobe spaceorb
# SpaceTec SpaceBall 4000 FLX 6dof controller:
#/sbin/modprobe spaceball
# Gravis Stinger gamepad:
#/sbin/modprobe stinger
# I-Force joysticks/wheels:
#/sbin/modprobe iforce
### Parallel port connected controllers ###
# Multisystem, Sega Genesis, Saturn joysticks and gamepads:
#/sbin/modprobe db9
# Multisystem, NES, SNES, N64, PSX joysticks and gamepads:
#/sbin/modprobe gamecon
# Multisystem joysticks via TurboGraFX device:
#/sbin/modprobe turbografx

### Appletalk support ###
# This is needed if you want to run netatalk, a package which allows
# you to use you Linux box as a file and print server for Apple Macintosh
# computers on your local network.
#/sbin/modprobe appletalk

### IPX networking support ###
#/sbin/modprobe ipx

### IDE device support ###
# IDE CD-ROM drives:
#/sbin/modprobe ide-cd
# IDE hard drives:
#/sbin/modprobe ide-disk
# IDE floppy drives:
#/sbin/modprobe ide-floppy
# IDE tape drives:
#/sbin/modprobe ide-tape

### Network device support ###
# Most of these drivers will probe automatically for the card if you don't
# specify an I/O address and IRQ. But, the NE2000 driver needs at least the
# I/O. For complete information, see the net-modules.txt file that comes
# with the Linux 2.2.x source code. This file can also be found on the
# Slackware CD-ROM in the /docs/linux-2.2.x/ directory.
#
# First, if setup probing found a network card, there may be an 'rc.netdevice'
# file that we should run to load the network module:
if [ -x /etc/rc.d/rc.netdevice ]; then
. /etc/rc.d/rc.netdevice
fi
### Ethernet cards based on the 8390 chip.
# 3com 3c503 support:
#/sbin/modprobe 3c503
# Ansel Communications EISA 3200 support:
#/sbin/modprobe ac3200
# Cabletron E21xx support:
#/sbin/modprobe e2100
# HP PCLAN+ (27247B and 27252A) support:
#/sbin/modprobe hp-plus
# HP PCLAN (27245 and other 27xxx series) support:
#/sbin/modprobe hp
# NE2000/NE1000 support (non PCI):
#/sbin/modprobe ne io=0x300 # NE2000 at 0x300
#/sbin/modprobe ne io=0x280 # NE2000 at 0x280
#/sbin/modprobe ne io=0x320 # NE2000 at 0x320
#/sbin/modprobe ne io=0x340 # NE2000 at 0x340
#/sbin/modprobe ne io=0x360 # NE2000 at 0x360
# PCI NE2000 clone support:
#/sbin/modprobe ne2k-pci
# SMC Ultra support:
#/sbin/modprobe smc-ultra
# SMC Ultra32 EISA support:
#/sbin/modprobe smc-ultra32
# Western Digital WD80*3 (and clones) support:
#/sbin/modprobe wd
#
# Other network hardware drivers:
#
# 3com 3c501 (consider buying a new card, since the 3c501 is slow,
# broken, and obsolete):
#/sbin/modprobe 3c501
# 3com 3c503:
#/sbin/modprobe 3c503
# 3com 3c505:
#/sbin/modprobe 3c505
# 3com 3c507:
#/sbin/modprobe 3c507
# 3com 3c509 and 3c579:
#/sbin/modprobe 3c509
# 3com 3c515:
#/sbin/modprobe 3c515
# This one works for all 3com 3c590/3c592/3c595/3c597 and the
# EtherLink XL 3c900 and 3c905 cards:
#/sbin/modprobe 3c59x
# Apricot Xen-II on board Ethernet:
#/sbin/modprobe apricot
# Generic ARCnet support:
#/sbin/modprobe arcnet
# AT1700/1720 support:
#/sbin/modprobe at1700
# AT-LAN-TEC/RealTek pocket adapter support:
#/sbin/modprobe atp
# BPQ Ethernet driver:
#/sbin/modprobe bpqether
# Generic DECchip & DIGITAL EtherWORKS PCI/EISA:
#/sbin/modprobe de4x5
# D-Link DE600 pocket adapter support:
#/sbin/modprobe de600
# D-Link DE620 pocket adapter support:
#/sbin/modprobe de620
# DEPCA support:
#/sbin/modprobe depca
# Digi International RightSwitch cards:
#/sbin/modprobe dgrs
# Intel EtherExpress Pro support:
#/sbin/modprobe eepro
# Intel EtherExpress PRO/100 PCI support:
#/sbin/modprobe eepro100
# Intel EtherExpress16 support:
#/sbin/modprobe eexpress
# SMC EtherPower II 9432 PCI support:
#/sbin/modprobe epic100
# ICL EtherTeam 16i/32 support:
#/sbin/modprobe eth16i
# DEC EtherWorks 3 support:
#/sbin/modprobe ewrk3
# Fujitsu FMV-181/182/183/184 support:
#/sbin/modprobe fmv18x
# HP 10/100VG PCLAN (ISA, EISA, PCI) support:
#/sbin/modprobe hp100
# IBM Tropic chipset based adapter support:
#/sbin/modprobe ibmtr
# AMD LANCE and PCnet (AT1500 and NE2100) support:
#/sbin/modprobe lance
# National Semiconductor DP8381x series PCI Ethernet support:
#/sbin/modprobe natsemi
# NI5210 support:
#/sbin/modprobe ni52
# NI6510 support:
#/sbin/modprobe ni65
# AMD PCnet32 (VLB and PCI) support:
#/sbin/modprobe pcnet32
# Red Creek Hardware Virtual Private Network (VPN) support:
#/sbin/modprobe rcpci
# RealTek 8129/8139 (not 8019/8029!) support:
#/sbin/modprobe 8139too
# RealTek 8139C+ enhanced support:
#/sbin/modprobe 8139cp
# Sangoma S502A FRAD support:
#/sbin/modprobe sdla
# SMC 9194 support:
#/sbin/modprobe smc9194
# TI ThunderLAN support:
#/sbin/modprobe tlan
# DECchip Tulip (dc21x4x) PCI support:
#/sbin/modprobe tulip
# VIA Rhine support:
#/sbin/modprobe via-rhine
# AT&T WaveLAN & DEC RoamAbout DS support:
#/sbin/modprobe wavelan
# Packet Engines Yellowfin Gigabit-NIC support:
#/sbin/modprobe yellowfin
# Davicom DM9xxx (9102/9132/9100/9802...)
#/sbin/modprobe dmfe
# SiS 900/7016 PCI Fast Ethernet
#/sbin/modprobe sis900

### Serial line load balancing support ###
#/sbin/modprobe eql

### "dummy" IP support ###
# A dummy IP driver. Essentially a loopback device. Can be useful --
# see the Network Administrator's Guide from sunsite.unc.edu:/pub/Linux/docs/LDP
#/sbin/modprobe dummy

### ISDN kernel support ###
#/sbin/modprobe isdn
# ISDN loop (provides a virtual ISDN card for testing):
#/sbin/modprobe isdnloop

### ISDN interface support ###
# AVM-B1 with CAPI2.0 driver (requires additional firmware; see
# /usr/src/linux/Documentation/isdn/README.avmb1):
#/sbin/modprobe capidrv
# HiSax SiemensChipSet driver (supports AVM A1, Elsa ISDN cards,
# Teles S0-16.0, Teles S0-16.3, Teles S0-8, Teles/Creatix PnP,
# ITK micro ix1 and many compatibles):
#/sbin/modprobe hisax
# IBM Active 2000 ISDN card support (requires additional firmware; see
# /usr/src/linux/Documentation/isdn/README.act2000 for more information)
#/sbin/modprobe act2000
# ICN active ISDN card driver:
#/sbin/modprobe icn
# PCBIT-D driver (requires additional firmware; see
# /usr/src/linux/Documentation/isdn/README.pcbit for more information)
#/sbin/modprobe pcbit
# Spellcaster BRI ISDN driver:
#/sbin/modprobe sc

### Binary format support ###
#/sbin/modprobe binfmt_aout
#/sbin/modprobe binfmt_elf
#/sbin/modprobe binfmt_java
#/sbin/modprobe binfmt_misc

### Filesystem support ###
#/sbin/modprobe adfs
#/sbin/modprobe affs
#/sbin/modprobe coda
#/sbin/modprobe cramfs
#/sbin/modprobe ext2
#/sbin/modprobe ext3
#/sbin/modprobe fat
#/sbin/modprobe hfs
#/sbin/modprobe hfsplus
#/sbin/modprobe hpfs
#/sbin/modprobe intermezzo
#/sbin/modprobe isofs
#/sbin/modprobe jfs
#/sbin/modprobe minix
#/sbin/modprobe msdos
#/sbin/modprobe ncpfs
#/sbin/modprobe nfs
#/sbin/modprobe ntfs
#/sbin/modprobe qnx4
#/sbin/modprobe reiserfs
#/sbin/modprobe romfs
#/sbin/modprobe smbfs
#/sbin/modprobe sysv
#/sbin/modprobe udf
#/sbin/modprobe ufs
#/sbin/modprobe umsdos
#/sbin/modprobe vfat
#/sbin/modprobe xfs

### RAID (Multiple Devices) support ###
#/sbin/modprobe linear
#/sbin/modprobe raid0
#/sbin/modprobe raid1
#/sbin/modprobe raid5

# *** THIS IS LOADED BY DEFAULT FOR 2.4.x KERNELS ***
# Note: this should no longer be needed to burn discs with 2.6.x.
#
# SCSI emulation support. This will provide SCSI host adapter emulation
# for IDE ATAPI devices, and will allow you to use a SCSI device driver
# instead of a native ATAPI driver. This is useful if you have an ATAPI
# device for which no native driver has been written (for example, an ATAPI
# PD-CD or CD-RW drive); you can then use this emulation together with an
# appropriate SCSI device driver. Note that this option does NOT allow you
# to attach SCSI devices to a box that doesn't have a SCSI host adapter
# installed. Also, you'll need to exclude your CD-RW from being grabbed by
# the normal ATAPI driver by passing a flag to the kernel at boot time.
# If you're using LILO, add this: append="hdc=ide-scsi"
# Replace "hdc" with the appropriate device name.
if cat /proc/sys/kernel/osrelease | cut -f 1,2 -d . | grep -w 2.4 1> /dev/null 2> /dev/null ; then
/sbin/modprobe ide-scsi
fi

# SCSI kernel support:
#/sbin/modprobe scsi_mod
#/sbin/modprobe scsi_syms
#/sbin/modprobe sd_mod
#/sbin/modprobe sg
#/sbin/modprobe sr_mod
#/sbin/modprobe st

# SCSI controller support:
# NCR53c7,8xx SCSI support (note there is another driver for
# the 53c8xx family below):
#/sbin/modprobe 53c7,8xx
# AM53/79C974 PCI SCSI support:
#/sbin/modprobe AM53C974
# BusLogic MultiMaster and FlashPoint SCSI support:
#/sbin/modprobe BusLogic
# NCR53c406a SCSI support:
#/sbin/modprobe NCR53c406a
# Initio INI-A100U2W SCSI support:
#/sbin/modprobe a100u2w
# AdvanSys SCSI support:
#/sbin/modprobe advansys
# Adaptec AHA152X/2825 support:
#/sbin/modprobe aha152x
# Adaptec AHA1542 support:
#/sbin/modprobe aha1542
# Adaptec AHA1740 support:
#/sbin/modprobe aha1740
# This is support for the various aic7xxx based Adaptec SCSI
# controllers. These include the 274x EISA cards; 284x VLB cards;
# 2902, 2910, 293x, 294x, 394x, 3985 and several other PCI and
# motherboard based SCSI controllers from Adaptec:
#/sbin/modprobe aic7xxx
# ACARD 870U/W SCSI support:
#/sbin/modprobe atp870u
# DTC 3180/3280 SCSI support:
#/sbin/modprobe dtc
# EATA ISA/EISA/PCI (DPT and generic EATA/DMA-compliant boards) support:
#/sbin/modprobe eata
# EATA-DMA [Obsolete -- use above driver] (DPT, NEC, AT&T, SNI, AST,
# Olivetti, Alphatronix) support:
#/sbin/modprobe eata_dma
# EATA-PIO (old DPT PM2001, PM2012A) support:
#/sbin/modprobe eata_pio
# Future Domain 16xx SCSI/AHA-2920A support:
#/sbin/modprobe fdomain
# Generic NCR5380/53c400 SCSI support:
#/sbin/modprobe g_NCR5380
# GDT SCSI Disk Array Controller support:
#/sbin/modprobe gdth
# IOMEGA parallel port (imm - newer drives like ZipPlus):
#/sbin/modprobe imm
# Always IN2000 SCSI support:
#/sbin/modprobe in2000
# Initio 91XXU(W) SCSI support:
#/sbin/modprobe initio
# AMI MegaRAID support:
#/sbin/modprobe megaraid
# NCR53C8XX SCSI support:
#/sbin/modprobe ncr53c8xx
# PAS16 SCSI support:
#/sbin/modprobe pas16
# PCI2000 support:
#/sbin/modprobe pci2000
# PCI2220i support:
#/sbin/modprobe pci2220i
# IOMEGA parallel port (ppa - older parallel Zip drives):
#/sbin/modprobe ppa
# PSI240i support:
#/sbin/modprobe psi240i
# Qlogic FastSCSI! cards:
#/sbin/modprobe qlogicfas
# QLogic ISP2100 SCSI support:
#/sbin/modprobe qlogicfc
# This driver works for all QLogic PCI SCSI host adapters (IQ-PCI,
# IQ-PCI-10, IQ_PCI-D) except for the PCI-basic card. (This latter
# card is supported by the "AM53/79C974 PCI SCSI" driver):
#/sbin/modprobe qlogicisp
# Seagate ST-02 and Future Domain TMC-8xx SCSI support:
#/sbin/modprobe seagate
# Symbios Logic sym53c416 support:
#/sbin/modprobe sym53c416
# Trantor T128/T128F/T228 SCSI support:
#/sbin/modprobe t128
# Tekram DC390(T) and Am53/79C974 (PCscsi) SCSI support:
#/sbin/modprobe tmscsim
# UltraStor 14F and 34F support (also see driver below):
#/sbin/modprobe u14-34f
# UltraStor 14F, 24F, and 34F support:
#/sbin/modprobe ultrastor
# Western Digital 7000 SCSI support:
#/sbin/modprobe wd7000

# Floppy drive support:
# (Most Linux kernels should already contain this)
#/sbin/modprobe floppy

# Floppy tape support (such as Colorado Jumbo 250 or other QIC-80 drives):
#/sbin/modprobe ftape

# IP masquerading modules:
# These modules are used with IP masquerading, a process which allows you to
# use a Linux box connected to the Internet (via PPP or SLIP, or some other
# means) as a gateway for other Linux, Windows, Macintosh boxes on your local
# network that don't have real IP addresses on the Internet. The packets
# going through the Linux machine are "masqueraded", or made to look as if
# they're all coming from the one real IP address on the Internet.
#
# As a quick example (for a much more extensive treatment, see the IP-Masquerade
# mini-HOWTO) to allow Internet access to a local network 192.168.11.0 with a
# netmask of 255.255.255.0, you'd use these commands in /etc/rc.d/rc.local:
#
# # EXTERNAL -> external network interface
# # INTERNAL -> internal network interface
# EXTERNAL=eth0
# INTERNAL=eth1
# echo 1 > /proc/sys/net/ipv4/ip_forward
# echo "Setting up NAT (Network Address Translation)..."
# # by default, nothing is forwarded.
# iptables -P FORWARD DROP
# # Allow all connections OUT and only related ones IN
# iptables -A FORWARD -i $EXTERNAL -o $INTERNAL -m state --state ESTABLISHED,RELATED -j ACCEPT
# iptables -A FORWARD -i $INTERNAL -o $EXTERNAL -j ACCEPT
# # enable MASQUERADING
# iptables -t nat -A POSTROUTING -o $EXTERNAL -j MASQUERADE
#
# Then you'd have to set the other boxes on your local network to use the
# Linux machine as their TCP/IP gateway. You'll probably also need to plug
# in the IP address for your Internet service provider in each machine's DNS
# setup.
#
# Now, on to the IP masquerading modules. The example above is good enough
# for most things that use TCP in a relatively simple fashion. It'll work
# for telnet and http, for instance. But, the system breaks down when you
# get protocols that use ports in more complicated ways. Luckily the Linux
# kernel gurus have thought of this and have prepared some modules that
# support masquerading of trickier protocols. The ipchains command is mighty
# flexible as well, and a lot of things can be made to work just by setting
# that up correctly.
#
# Special modules for iptables. See also "man iptables" for information about
# that powerfull firewall tool.
#
#/sbin/modprobe ipt_conntrack
#/sbin/modprobe ip_conntrack
#/sbin/modprobe ip_conntrack_ftp
#/sbin/modprobe ip_conntrack_irc
#/sbin/modprobe ip_nat_ftp
#/sbin/modprobe ip_nat_irc
#/sbin/modprobe ip_nat_snmp_basic
#
# These modules below are for ipchains (kernel 2.2.x). You can install ipchains
# from /pasture. To use ipchains with newer kernels, you'll need this:
# /sbin/modprobe ipchains
#
#/sbin/modprobe ip_masq_autofw
#/sbin/modprobe ip_masq_cuseeme
#/sbin/modprobe ip_masq_ftp
#/sbin/modprobe ip_masq_irc
#/sbin/modprobe ip_masq_mfw
#/sbin/modprobe ip_masq_portfw
#/sbin/modprobe ip_masq_quake
#/sbin/modprobe ip_masq_raudio
#/sbin/modprobe ip_masq_user
#/sbin/modprobe ip_masq_vdolive

Messaggio da **phobos3576** » mer 19 lug 2006, 3:04

Non hai notato queste linee?

Codice: Seleziona tutto

### AGP (Accelerated Graphics Port) GART support ###
# This module takes care of programming the GART (part of your motherboard's
# chipset that handles gathering data from memory and passing it to the
# card) and enables faster AGP transfers. The AGP GART module is required
# to use AGP features of your 3D rendering video card. You'll need this to
# use XFree86's direct rendering support, for example.
if ! grep noagp /proc/cmdline; then
echo "[0;1mUse 'slax noagp' boot parameter to skip the following step:[0;0m"
/sbin/modprobe agpgart
fi

Commentale e riavvia il computer.

Ricontrollando il tuo /var/log/Xorg.0.log ho notato la seguente riga:

Codice: Seleziona tutto

Current Operating System: Linux slax 2.6.15.6 #1 SMP Fri Mar 24 16:46:23 GMT 2006 i686

Quindi, stai usando ancora il vecchio kernel?
E inoltre, la Slax è una distribuzione live; la stai eseguendo dal CD/DVD?